Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. #129

Calmact · 2022-03-01T16:56:43Z

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips of e900v22c/22d, etc.
Add x96max-u-boot.bin.sd.bin file as MAINLINE_UBOOT file
All tests are run on e900v22c.
Armbin (kernel 5.15) only supports boot from USB-flash-drive, not support from TF-card.
Armbin (kernel 5.4) supports boot from USB-flash-drive and TF-card, but both do not support the 100M wired ethernet on a chip.

Contributor: @zzcand111 zzcand111

ttl output with armbin (kernel 5.15) start in usb

 G12A:BL:0253b8:61aa2d;FEAT:E0F93180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                                          bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000701
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f93180

TE: 90426

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000027 00000027 00000025 00000026 00000026 00000027 00000026 00000026 00000025 00000025 00000027 00000026 00000025 00000027 00000025 00000027 00000024 00000025 00000023 00000024 00000027 00000027 00000026 00000024 00000027 00000025 00000026 00000025 00000025 00000026 00000025 00000025 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 429
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0b 70 00 01 35 2c 00 00 01 32 38 30 4b 41 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** File not found /logo_files/bootup.bmp **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,3839,0,2159
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[2160p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 97
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 11  vid_clk_div = 1
hdmitx: set enc for VIC: 353
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 2160p60hz, attr: 420,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card out
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 3000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
reading s905_autoscript
1654 bytes read in 33 ms (48.8 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
card out
** Bad device mmc 0 **
reading boot_android
** Unable to read file boot_android **
card out
** Bad device mmc 0 **
reading u-boot.ext
694755 bytes read in 73 ms (9.1 MiB/s)
## Starting application at 0x01000000 ...


U-Boot 2021.04-00056-g13ac02db31-dirty (Apr 28 2021 - 22:44:20 +0800) u200

Model: Amlogic Meson G12A U200 Development Board
SoC:   Amlogic Meson G12A (Unknown) Revision 28:b (70:2)
DRAM:  2 GiB
MMC:   sd@ffe05000: 0, mmc@ffe07000: 1
Loading Environment from nowhere... OK
In:    serial@3000
Out:   serial@3000
Err:   serial@3000
Net:   eth0: ethernet@ff3f0000
Hit any key to stop autoboot:  0
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... 3 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found

Device 0: Vendor: Kingston Rev: PMAP Prod: DataTraveler 3.0
            Type: Removable Hard Disk
            Capacity: 14784.0 MB = 14.4 GB (30277632 x 512)
... is now current device
Scanning usb 0:1...
Found U-Boot script /boot.scr
1123 bytes read in 1 ms (1.1 MiB/s)
## Executing script at 08000000
Start AMLOGIC mainline U-boot
## Error: "bootfromsd" not defined
336 bytes read in 1 ms (328.1 KiB/s)
## Error: "mac" not defined
## Error: "eth_mac" not defined
ethaddr=36:3e:5e:ea:04:7b
25934336 bytes read in 595 ms (41.6 MiB/s)
7381283 bytes read in 169 ms (41.7 MiB/s)
72049 bytes read in 4 ms (17.2 MiB/s)
Moving Image from 0x8080000 to 0x8200000, end=9ba0000
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    7381219 Bytes = 7 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 08008000
   Booting using the fdt blob at 0x8008000
   Loading Ramdisk to 3f8f5000, end 3ffff0e3 ... OK
   Loading Device Tree to 000000003f8e0000, end 000000003f8f4970 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.15.25-flippy-70+ (root@univm25) (Ubuntu clang version 13.0.0-9, Ubuntu LLD 13.0.0) #75 SMP PREEMPT Sat Feb 26 14:27:00 CST 2022
[    0.000000] Machine model: Amlogic Meson G12A U200 Development Board
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000070000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000004ffffff]
[    0.000000]   node   0: [mem 0x0000000005000000-0x00000000072fffff]
[    0.000000]   node   0: [mem 0x0000000007300000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 19 pages/cpu s37400 r8192 d32232 u77824
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516096
[    0.000000] Kernel command line: root=UUID=facec5be-7f03-4d78-abc8-675e728dc9cf rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 mac=36:3e:5e:ea:04:7b
[    0.000000] Unknown kernel command line parameters "cgroup_enable=memory cgroup_memory=1 mac=36:3e:5e:ea:04:7b", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1729060K/2097152K available (14784K kernel code, 2670K rwdata, 5720K rodata, 2048K init, 880K bss, 105948K reserved, 262144K cma-reserved)
[    0.000000] random: get_random_u64 called from kmem_cache_open+0x28/0x534 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000245] Console: colour dummy device 80x25
[    0.000656] printk: console [tty0] enabled
[    0.000713] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.000738] pid_max: default: 32768 minimum: 301
[    0.000828] LSM: Security Framework initializing
[    0.000905] SELinux:  Initializing.
[    0.001029] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.001056] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.002762] rcu: Hierarchical SRCU implementation.
[    0.004179] EFI services will not be available.
[    0.004508] smp: Bringing up secondary CPUs ...
[    0.005087] Detected VIPT I-cache on CPU1
[    0.005149] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.005747] Detected VIPT I-cache on CPU2
[    0.005777] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006339] Detected VIPT I-cache on CPU3
[    0.006366] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006437] smp: Brought up 1 node, 4 CPUs
[    0.006500] SMP: Total of 4 processors activated.
[    0.006512] CPU features: detected: 32-bit EL0 Support
[    0.006523] CPU features: detected: 32-bit EL1 Support
[    0.006536] CPU features: detected: CRC32 instructions
[    0.007376] CPU: All CPU(s) started at EL2
[    0.007408] alternatives: patching kernel code
[    0.009279] devtmpfs: initialized
[    0.021811] Registered cp15_barrier emulation handler
[    0.021853] Registered setend emulation handler
[    0.021983] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.022015] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.032005] prandom: seed boundary self test passed
[    0.033615] prandom: 100 self tests passed
[    0.057437] prandom32: self test passed (less than 6 bits correlated)
[    0.057492] pinctrl core: initialized pinctrl subsystem
[    0.058139] DMI not present or invalid.
[    0.058409] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.060238] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.060413] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.060614] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.060697] audit: initializing netlink subsys (disabled)
[    0.060856] audit: type=2000 audit(0.059:1): state=initialized audit_enabled=0 res=1
[    0.062148] thermal_sys: Registered thermal governor 'step_wise'
[    0.062674] cpuidle: using governor ladder
[    0.062844] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.062958] ASID allocator initialised with 65536 entries
[    0.063102] Serial: AMBA PL011 UART driver
[    0.086865] platform ff900000.vpu: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.094418] platform cvbs-connector: Fixing up cyclic dependency with ff900000.vpu
[    0.095387] platform hdmi-connector: Fixing up cyclic dependency with ff600000.hdmi-tx
[    0.106456] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.106492] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.106507] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.106522] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    1.738197] cryptd: max_cpu_qlen set to 1000
[    1.741884] "cryptomgr_test" (94) uses obsolete ecb(arc4) skcipher
[    1.753110] alg: No test for 842 (842-generic)
[    1.753243] alg: No test for 842 (842-scomp)
[    1.854011] DRBG: Continuing without Jitter RNG
[    1.936377] raid6: neonx8   gen()  2214 MB/s
[    1.993135] raid6: neonx8   xor()  1590 MB/s
[    2.049905] raid6: neonx4   gen()  2097 MB/s
[    2.106652] raid6: neonx4   xor()  1482 MB/s
[    2.163426] raid6: neonx2   gen()  1938 MB/s
[    2.220180] raid6: neonx2   xor()  1418 MB/s
[    2.276957] raid6: neonx1   gen()  1664 MB/s
[    2.333699] raid6: neonx1   xor()  1202 MB/s
[    2.390488] raid6: int64x8  gen()  1423 MB/s
[    2.447218] raid6: int64x8  xor()   764 MB/s
[    2.503984] raid6: int64x4  gen()  1549 MB/s
[    2.560748] raid6: int64x4  xor()   808 MB/s
[    2.617505] raid6: int64x2  gen()  1356 MB/s
[    2.674261] raid6: int64x2  xor()   729 MB/s
[    2.731024] raid6: int64x1  gen()   947 MB/s
[    2.787780] raid6: int64x1  xor()   547 MB/s
[    2.787793] raid6: using algorithm neonx8 gen() 2214 MB/s
[    2.787805] raid6: .... xor() 1590 MB/s, rmw enabled
[    2.787817] raid6: using neon recovery algorithm
[    2.787970] fbcon: Taking over console
[    2.789463] VDDAO_3V3: supplied by 12V
[    2.789867] iommu: Default domain type: Translated
[    2.789881] iommu: DMA domain TLB invalidation policy: strict mode
[    2.790214] vgaarb: loaded
[    2.790651] SCSI subsystem initialized
[    2.790862] usbcore: registered new interface driver usbfs
[    2.790911] usbcore: registered new interface driver hub
[    2.790954] usbcore: registered new device driver usb
[    2.791387] mc: Linux media interface: v0.10
[    2.791422] videodev: Linux video capture interface: v2.00
[    2.791684] EDAC MC: Ver: 3.0.0
[    2.792674] Advanced Linux Sound Architecture Driver Initialized.
[    2.793693] clocksource: Switched to clocksource arch_sys_counter
[    2.793949] VFS: Disk quotas dquot_6.6.0
[    2.794012] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    2.794145] FS-Cache: Loaded
[    2.801231] NET: Registered PF_INET protocol family
[    2.801395] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    2.802527] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    2.802573] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    2.802740] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[    2.802997] TCP: Hash tables configured (established 16384 bind 16384)
[    2.803192] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear)
[    2.803270] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    2.803326] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    2.803503] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    2.803539] NET: Registered PF_XDP protocol family
[    2.803560] PCI: CLS 0 bytes, default 64
[    2.803885] Trying to unpack rootfs image as initramfs...
[    2.814348] kvm [1]: IPA Size Limit: 40 bits
[    2.817160] kvm [1]: vgic interrupt IRQ9
[    2.817383] kvm [1]: Hyp mode initialized successfully
[    3.301435] Freeing initrd memory: 7208K
[    3.505542] Initialise system trusted keyrings
[    3.505726] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[    3.512364] zbud: loaded
[    3.514196] fuse: init (API version 7.34)
[    3.514638] SGI XFS with ACLs, security attributes, quota, no debug enabled
[    3.553809] NET: Registered PF_ALG protocol family
[    3.605615] xor: measuring software checksum speed
[    3.609540]    8regs           :  2522 MB/sec
[    3.612946]    32regs          :  2906 MB/sec
[    3.617802]    arm64_neon      :  2036 MB/sec
[    3.617815] xor: using function: 32regs (2906 MB/sec)
[    3.617832] Key type asymmetric registered
[    3.617844] Asymmetric key parser 'x509' registered
[    3.617937] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    3.618057] io scheduler mq-deadline registered
[    3.618072] io scheduler kyber registered
[    3.618210] io scheduler bfq registered
[    3.688458] soc soc0: Amlogic Meson G12A (Unknown) Revision 28:b (70:2) Detected
[    3.689883] VDDCPU: supplied by 12V
[    3.691287] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    3.692988] Serial: AMBA driver
[    3.693381] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 22, base_baud = 1500000) is a meson_uart
[    4.687315] printk: console [ttyAML0] enabled
[    4.699993] brd: module loaded
[    4.703782] loop: module loaded
[    4.710773] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.711691] ehci-pci: EHCI PCI platform driver
[    4.716148] ehci-platform: EHCI generic platform driver
[    4.721745] usbcore: registered new interface driver cdc_wdm
[    4.726912] usbcore: registered new interface driver usb-storage
[    4.733256] mousedev: PS/2 mouse device common for all mice
[    4.739247] SPI driver rmi4_spi has no spi_device_id for syna,rmi4-spi
[    4.745487] meson-vrtc ff8000a8.rtc: registered as rtc0
[    4.750004] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)
[    4.758418] i2c_dev: i2c /dev entries driver
[    4.765829] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present!
[    4.770171] Registered IR keymap rc-cec
[    4.773733] rc rc0: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0
[    4.782387] input: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc0/input0
[    4.799598] Synopsys Designware Multimedia Card Interface Driver
[    4.800819] meson-gx-mmc ffe05000.sd: Got CD GPIO
[    4.801687] meson-sm: secure-monitor enabled
[    4.810249] hid: raw HID events driver (C) Jiri Kosina
[    4.814050] usbcore: registered new interface driver usbhid
[    4.819485] usbhid: USB HID core driver
[    4.826716] Initializing XFRM netlink socket
[    4.827864] NET: Registered PF_INET6 protocol family
[    4.833024] gpio irq setup: hwirq: 0x3B irqfirst: 0x35 irqlast: 0x3C pin[47]
[    4.839642] genirq: Setting trigger mode 3 for irq 36 failed (meson_gpio_irq_set_type+0x0/0x140)
[    4.859975] Segment Routing with IPv6
[    4.860014] RPL Segment Routing with IPv6
[    4.862045] In-situ OAM (IOAM) with IPv6
[    4.866006] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.874144] bpfilter: Loaded bpfilter_umh pid 300
[    4.876437] NET: Registered PF_PACKET protocol family
[    4.881466] NET: Registered PF_KEY protocol family
[    4.886265] 8021q: 802.1Q VLAN Support v1.8
[    4.890577] registered taskstats version 1
[    4.894369] Loading compiled-in X.509 certificates
[    4.900812] zswap: loaded using pool zstd/zbud
[    4.903863] Key type ._fscrypt registered
[    4.907458] Key type .fscrypt registered
[    4.911335] Key type fscrypt-provisioning registered
[    4.916864] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no
[    4.943096] VCC_3V3: supplied by VDDAO_3V3
[    4.943591] VCC_5V: supplied by 12V
[    4.945187] VDDAO_1V8: supplied by VDDAO_3V3
[    5.037099] meson-drm ff900000.vpu: Queued 3 outputs on vpu
[    5.067076] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    5.071794] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    5.079602] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops)
[    5.087145] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
[    5.207381] random: fast init done
[    5.213249] [drm] kms: can't enable cloning when we probably wanted to.
[    5.379876] Console: switching to colour frame buffer device 240x67
[    5.474999] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device
[    5.487397] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[    5.488623] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[    5.494966] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[    5.502309] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[    5.507790] meson8b-dwmac ff3f0000.ethernet:         DWMAC1000
[    5.513021] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[    5.520378] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[    5.527787] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[    5.532965] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[    5.539948] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[    5.546334] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[    5.552203] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[    5.557972] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    5.569252] FLASH_1V8: supplied by VCC_3V3
[    5.570454] USB_PWR_EN: supplied by VCC_5V
[    5.574207] VCC_1V8: supplied by VCC_3V3
[    5.587396] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[    5.587517] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[    5.595730] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator
[    5.599445] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator
[    5.606643] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    5.615059] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.619023] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    5.626582] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[    5.635791] xhci-hcd xhci-hcd.3.auto: irq 39, io mem 0xff500000
[    5.641912] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[    5.649796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.656942] usb usb1: Product: xHCI Host Controller
[    5.661772] usb usb1: Manufacturer: Linux 5.15.25-flippy-70+ xhci-hcd
[    5.668157] usb usb1: SerialNumber: xhci-hcd.3.auto
[    5.673323] hub 1-0:1.0: USB hub found
[    5.676719] hub 1-0:1.0: 2 ports detected
[    5.680926] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.686195] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    5.693697] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    5.700210] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.708326] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[    5.716373] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.723528] usb usb2: Product: xHCI Host Controller
[    5.728359] usb usb2: Manufacturer: Linux 5.15.25-flippy-70+ xhci-hcd
[    5.734743] usb usb2: SerialNumber: xhci-hcd.3.auto
[    5.739881] hub 2-0:1.0: USB hub found
[    5.743300] hub 2-0:1.0: 1 port detected
[    5.749523] ALSA device list:
[    5.749613] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[    5.752771]   No soundcards found.
[    5.784663] Freeing unused kernel memory: 2048K
[    5.788619] Run /init as init process
[    5.873110] mmc2: new HS200 MMC card at address 0001
[    5.876997] mmcblk2: mmc2:0001 SPeMMC 7.22 GiB
[    5.882864] mmcblk2boot0: mmc2:0001 SPeMMC 4.00 MiB
[    5.887727] mmcblk2boot1: mmc2:0001 SPeMMC 4.00 MiB
[    5.893031] mmcblk2rpmb: mmc2:0001 SPeMMC 4.00 MiB, chardev (240:0)
[    5.937063] usb 1-1: new full-speed USB device number 2 using xhci-hcd
[    6.084747] usb 1-1: New USB device found, idVendor=413c, idProduct=301c, bcdDevice= 2.28
[    6.090503] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    6.097758] usb 1-1: Product: Dell Universal Receiver
[    6.103834] usb 1-1: Manufacturer: Dell Computer Corp
[    6.127407] input: Dell Computer Corp Dell Universal Receiver as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.0/0003:413C:301C.0001/input/input1
[    6.201078] hid-generic 0003:413C:301C.0001: input,hidraw0: USB HID v1.11 Keyboard [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input0
[    6.218467] input: Dell Computer Corp Dell Universal Receiver Mouse as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input2
[    6.233340] input: Dell Computer Corp Dell Universal Receiver Consumer Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input3
[    6.304194] input: Dell Computer Corp Dell Universal Receiver System Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input4
[    6.324185] hid-generic 0003:413C:301C.0002: input,hidraw1: USB HID v1.11 Mouse [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input1
[    6.341494] hid-generic 0003:413C:301C.0003: hiddev96,hidraw2: USB HID v1.11 Device [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input2
[    6.477133] usb 1-2: new high-speed USB device number 3 using xhci-hcd
[    6.627422] usb 1-2: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 1.10
[    6.660601] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    6.689340] usb 1-2: Product: DataTraveler 3.0
[    6.704635] usb 1-2: Manufacturer: Kingston
[    6.716208] usb 1-2: SerialNumber: AC220B280C75B041293F58E8
[    6.725844] usb-storage 1-2:1.0: USB Mass Storage device detected
[    6.738931] scsi host0: usb-storage 1-2:1.0
[    7.770640] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6
[    7.793474] sd 0:0:0:0: [sda] 30277632 512-byte logical blocks: (15.5 GB/14.4 GiB)
[    7.816055] sd 0:0:0:0: [sda] Write Protect is off
[    7.831126] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    7.917259]  sda: sda1 sda2
[    7.937607] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    8.164461] EXT4-fs (sda2): mounted filesystem with writeback data mode. Opts: data=writeback. Quota mode: none.
[    8.666479] systemd[1]: System time before build time, advancing clock.
[    8.806389] systemd[1]: systemd 245.4-4ubuntu3.15 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    8.857773] systemd[1]: Detected architecture arm64.
[    8.922591] systemd[1]: Set hostname to <armbian>.
[    9.680588] random: systemd: uninitialized urandom read (16 bytes read)
[    9.693973] systemd[1]: Created slice system-modprobe.slice.
[    9.706504] random: systemd: uninitialized urandom read (16 bytes read)
[    9.714665] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    9.725713] random: systemd: uninitialized urandom read (16 bytes read)
[    9.733202] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    9.745386] systemd[1]: Created slice User and Session Slice.
[    9.755107] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[    9.767644] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.780592] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    9.794687] systemd[1]: Reached target Local Encrypted Volumes.
[    9.805309] systemd[1]: Reached target Slices.
[    9.815599] systemd[1]: Reached target Swap.
[    9.825787] systemd[1]: Reached target System Time Set.
[    9.852829] systemd[1]: Listening on RPCbind Server Activation Socket.
[    9.868316] systemd[1]: Listening on Syslog Socket.
[    9.881156] systemd[1]: Listening on fsck to fsckd communication Socket.
[    9.893483] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    9.905300] systemd[1]: Listening on Journal Audit Socket.
[    9.914886] systemd[1]: Listening on Journal Socket (/dev/log).
[    9.924809] systemd[1]: Listening on Journal Socket.
[    9.934568] systemd[1]: Listening on udev Control Socket.
[    9.944132] systemd[1]: Listening on udev Kernel Socket.
[    9.956745] systemd[1]: Mounting Huge Pages File System...
[    9.969916] systemd[1]: Mounting POSIX Message Queue File System...
[    9.983250] systemd[1]: Mounting RPC Pipe File System...
[    9.996632] systemd[1]: Mounting Kernel Debug File System...
[   10.006580] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   10.020994] systemd[1]: Starting Restore / save the current clock...
[   10.027561] RPC: Registered named UNIX socket transport module.
[   10.027572] RPC: Registered udp transport module.
[   10.027574] RPC: Registered tcp transport module.
[   10.027577] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.055060] systemd[1]: Starting Set the console keyboard layout...
[   10.069067] systemd[1]: Starting Create list of static device nodes for the current kernel...
[   10.081274] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
[   10.084728] systemd[1]: Started Nameserver information manager.
[   10.099254] systemd[1]: Reached target Network (Pre).
[   10.112005] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   10.119911] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   10.134121] systemd[1]: Starting Load Kernel Modules...
[   10.146772] systemd[1]: Starting Remount Root and Kernel File Systems...
[   10.160636] systemd[1]: Starting udev Coldplug all Devices...
[   10.171995] usbcore: registered new interface driver r8152
[   10.172061] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro. Quota mode: none.
[   10.175328] systemd[1]: Mounted Huge Pages File System.
[   10.196768] systemd[1]: Mounted POSIX Message Queue File System.
[   10.201873] usbcore: registered new interface driver ax88179_178a
[   10.211188] systemd[1]: Mounted RPC Pipe File System.
[   10.220408] systemd[1]: Mounted Kernel Debug File System.
[   10.231163] systemd[1]: Finished Restore / save the current clock.
[   10.242811] systemd[1]: Finished Create list of static device nodes for the current kernel.
[   10.260125] systemd[1]: Finished Load Kernel Modules.
[   10.271243] systemd[1]: Finished Remount Root and Kernel File Systems.
[   10.285777] systemd[1]: Mounting FUSE Control File System...
[   10.298006] systemd[1]: Mounting Kernel Configuration File System...
[   10.309409] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   10.316540] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   10.329000] systemd[1]: Starting Load/Save Random Seed...
[   10.341551] systemd[1]: Starting Apply Kernel Variables...
[   10.354067] systemd[1]: Starting Create System Users...
[   10.368218] systemd[1]: Finished Set the console keyboard layout.
[   10.380882] systemd[1]: Mounted FUSE Control File System.
[   10.391066] systemd[1]: Mounted Kernel Configuration File System.
[   10.402652] systemd[1]: Finished Apply Kernel Variables.
[   10.510003] systemd[1]: Finished Create System Users.
[   10.522649] systemd[1]: Starting Create Static Device Nodes in /dev...
[   10.556809] systemd[1]: Finished Create Static Device Nodes in /dev.
[   10.571546] systemd[1]: Finished udev Coldplug all Devices.
[   10.584362] systemd[1]: Reached target Local File Systems (Pre).
[   10.601307] systemd[1]: Mounting /var/tmp...
[   10.616932] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[   10.633139] systemd[1]: Starting udev Kernel Device Manager...
[   10.646376] systemd[1]: Mounted /var/tmp.
[   10.738875] systemd[1]: Started udev Kernel Device Manager.
[   11.005671] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   11.039736] random: crng init done
[   11.043936] random: 7 urandom warning(s) missed due to ratelimiting
[   11.050288] systemd[1]: Found device /dev/ttyAML0.
[   11.069219] systemd[1]: Finished Load/Save Random Seed.
[   11.089097] Registered IR keymap rc-empty
[   11.107493] panfrost ffe40000.gpu: clock rate = 24000000
[   11.111778] panfrost ffe40000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19
[   11.111912] rc rc1: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1
[   11.128755] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0
[   11.135626] panfrost ffe40000.gpu: features: 00000000,3fde77ff, issues: 00000000,00000400
[   11.137196] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[   11.143228] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7
[   11.143243] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1
[   11.170987] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1/input5
[   11.177609] [drm] Initialized panfrost 1.2.0 20180908 for ffe40000.gpu on minor 1
[   11.193752] meson-ir ff808000.ir: receiver initialized
[   11.194662] debugfs: File 'Capture' in directory 'dapm' already present!
[   11.256157] systemd[1]: Found device /sys/subsystem/net/devices/eth0.
[   11.292876] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   11.303212] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   11.315574] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   11.325432] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   11.333381] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   11.342433] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   11.353034] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   11.412901] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   11.426331] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   11.434361] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   11.434517] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   11.434701] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   11.434820] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   11.606097] systemd[1]: Found device DataTraveler_3.0 BOOT.
[   11.620825] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[   11.648521] systemd[1]: Started File System Check Daemon to report status.
[   11.670710] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[   11.775204] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[   11.796624] systemd[1]: Mounting /boot...
[   11.837704] systemd[1]: Mounted /boot.
[   11.853018] systemd[1]: Reached target Local File Systems.
[   11.871746] systemd[1]: Starting Armbian ZRAM config...
[   11.887273] systemd[1]: Starting Set console font and keymap...
[   11.901771] systemd[1]: Started ifup for eth0.
[   11.915265] systemd[1]: Starting Raise network interfaces...
[   11.928149] systemd[1]: Starting Preprocess NFS configuration...
[   11.943673] systemd[1]: Starting Mark the need to relabel after reboot...
[   11.954025] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[   11.962825] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   11.973155] systemd[1]: nfs-config.service: Succeeded.
[   11.979757] systemd[1]: Finished Preprocess NFS configuration.
[   11.994560] systemd[1]: Finished Mark the need to relabel after reboot.
[   12.005736] systemd[1]: Condition check resulted in RPC security service for NFS client and server being skipped.
[   12.015580] systemd[1]: Reached target NFS client services.
[   12.120530] zram: Added device: zram0
[   12.125611] zram: Added device: zram1
[   12.130642] zram: Added device: zram2
[   12.301588] zram0: detected capacity change from 0 to 2000464
[   12.340567] Adding 1000228k swap on /dev/zram0.  Priority:5 extents:1 across:1000228k SSFS
[   12.437688] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.1:08] driver [Meson G12A Internal PHY] (irq=37)
[   12.437947] zram1: detected capacity change from 0 to 102400
[   12.451894] meson8b-dwmac ff3f0000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
[   12.467057] meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
[   12.473291] meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
[   12.480475] meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rmii link mode
[   12.506491] zram2: detected capacity change from 0 to 2000464
[   12.562069] EXT4-fs (zram2): mounted filesystem without journal. Opts: discard. Quota mode: none.
[   12.586830] systemd[1]: Finished Armbian ZRAM config.
[   12.600327] systemd[1]: Starting Armbian memory supported logging...
[   12.661848] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard. Quota mode: none.
[   12.669321] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   14.073466] meson8b-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[   14.080881] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   14.968900] systemd[1]: Finished Armbian memory supported logging.
[   14.983957] systemd[1]: Starting Journal Service...
[   15.125305] systemd[1]: Started Journal Service.
[   15.158666] systemd-journald[843]: Received client request to flush runtime journal.
[   15.324998] [drm] kms: can't enable cloning when we probably wanted to.

armbian login: root (automatic login)

    _              _        ___   ___  ____  _ _____
   / \   _ __ ___ | |  ___ / _ \ / _ \| ___|| |___ /  __ _
  / _ \ | '_ ` _ \| | / __| (_) | | | |___ \| | |_ \ / _` |
 / ___ \| | | | | | | \__ \\__, | |_| |___) | |___) | (_| |
/_/   \_\_| |_| |_|_| |___/  /_/ \___/|____/|_|____/ \__,_|

Welcome to Armbian 22.05.0-trunk Focal with Linux 5.15.25-flippy-70+

No end-user support: built from trunk

System load:   52%              Up time:       0 min
Memory usage:  7% of 1.91G      IP:            192.168.30.110
192.168.30.111
CPU temp:      46°C             Usage of /:    44% of 2.6G
storage/:      41% of 243M

[ General system configuration (beta): armbian-config ]

Calmact · 2022-03-01T17:09:52Z

boot from tf card is not support

G12A:BL:0253b8:61aa2d;FEAT:E0F93180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                       bl2_stage                                                                                                             _init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000701
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f93180

TE: 107222

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000,                                                                                                              part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000                                                                                                             , part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@                                                                                                             droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000027 00000027 00000025 00000026 00000026 00000028 0000                                                                                                             0027 00000026 00000025 00000025 00000027 00000026 00000026 00000027 00000025 000                                                                                                             00027 00000024 00000025 00000023 00000024 00000027 00000027 00000026 00000024 00                                                                                                             000027 00000025 00000026 00000025 00000025 00000027 00000025 00000025 dwc_ddrphy                                                                                                             _apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 429
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part                                                                                                             : 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0b 70 00 01 35 2c 00 00 01 32 38 30 4b 41 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** File not found /logo_files/bootup.bmp **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,3839,0,2159
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[2160p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 97
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 11  vid_clk_div = 1
hdmitx: set enc for VIC: 353
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 2160p60hz, attr: 420,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card in
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 9c
OEM: 534f
Name: USD00
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: (0x762f00000 Bytes) 29.5 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
1654 bytes read in 4 ms (403.3 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
reading boot_android
** Unable to read file boot_android **
** Bad device usb 0 **
reading u-boot.ext
694755 bytes read in 45 ms (14.7 MiB/s)
## Starting application at 0x01000000 ...


U-Boot 2021.04-00056-g13ac02db31-dirty (Apr 28 2021 - 22:44:20 +0800) u200

Model: Amlogic Meson G12A U200 Development Board
SoC:   Amlogic Meson G12A (Unknown) Revision 28:b (70:2)
DRAM:  2 GiB
MMC:   sd@ffe05000: 0, mmc@ffe07000: 1
Loading Environment from nowhere... OK
In:    serial@3000
Out:   serial@3000
Err:   serial@3000
Net:   eth0: ethernet@ff3f0000
Hit any key to stop autoboot:  0
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
1123 bytes read in 1 ms (1.1 MiB/s)
## Executing script at 08000000
Start AMLOGIC mainline U-boot
## Error: "bootfromsd" not defined
unable to select a mode : -110
SCRIPT FAILED: continuing...
unable to select a mode : -110
unable to select a mode : -110
unable to select a mode : -110
unable to select a mode : -110
unable to select a mode : -110
unable to select a mode : -110
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk sd@ffe05000.blk...
unable to select a mode : -110
Scanning disk mmc@ffe07000.blk...
 ** fs_devread read error - block
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
Found 4 disks
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
unable to select a mode : -110
unable to select a mode : -110
MMC Device 2 not found
no mmc device at slot 2
Speed: 100, full duplex
BOOTP broadcast 1
*** Unhandled DHCP Option in OFFER/ACK: 43
*** Unhandled DHCP Option in OFFER/ACK: 43
DHCP client bound to address 192.168.30.103 (6 ms)
*** Warning: no boot file name; using 'C0A81E67.img'
Using ethernet@ff3f0000 device
TFTP from server 192.168.30.1; our IP address is 192.168.30.103
Filename 'C0A81E67.img'.
Load address: 0x44000000
Loading: T T T

Calmact · 2022-03-01T17:24:05Z

armbian with kernel 5.4 is bootable from TF,
but without 100M eth0 ethernet
with error

meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   18.367945] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

full ttl output

G12A:BL:0253b8:61aa2d;FEAT:E0F93180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                       bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000701
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f93180

TE: 113956

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000027 00000027 00000025 00000026 00000026 00000028 00000026 00000026 00000025 00000025 00000027 00000026 00000026 00000027 00000025 00000027 00000025 00000025 00000023 00000024 00000026 00000027 00000026 00000024 00000027 00000025 00000026 00000025 00000025 00000026 00000025 00000025 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 433
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0b 70 00 01 35 2c 00 00 01 32 38 30 4b 41 50
[0.014271 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** File not found /logo_files/bootup.bmp **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,3839,0,2159
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[2160p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 97
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 11  vid_clk_div = 1
hdmitx: set enc for VIC: 353
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 2160p60hz, attr: 420,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card in
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 400000
co-phase 0x2, tx-dly 0, clock 40000000
init_part() 282: PART_TYPE_DOS
[mmc_init] mmc init success
Device: SDIO Port B
Manufacturer ID: 9c
OEM: 534f
Name: USD00
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: (0x762f00000 Bytes) 29.5 GiB
mmc clock: 40000000
Bus Width: 4-bit
reading s905_autoscript
1654 bytes read in 4 ms (403.3 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
reading boot_android
** Unable to read file boot_android **
** Bad device usb 0 **
reading u-boot.ext
** Unable to read file u-boot.ext **
** Bad device usb 0 **
reading uEnv.txt
336 bytes read in 5 ms (65.4 KiB/s)
mac=A0:4C:0C:04:13:81
reading /zImage
20685312 bytes read in 1153 ms (17.1 MiB/s)
reading /uInitrd
6190008 bytes read in 343 ms (17.2 MiB/s)
reading /dtb/amlogic/meson-g12a-u200.dtb
45932 bytes read in 10 ms (4.4 MiB/s)
## Error: "aadmac" not defined
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] fdt get prop fail.
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    6189944 Bytes = 5.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
find 1 dtbos
No androidboot.dtbo_idx configured
And no dtbos will be applied
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] fdt get prop fail.
   Loading Ramdisk to 7384b000, end 73e32378 ... OK
   Loading Device Tree to 000000001fff1000, end 000000001ffff421 ... OK
fdt_fixup_memory_banks, reg:000000001fffb2f8
DTS already have 'reg' property

Starting kernel ...

uboot time: 5090719 us
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.4.181-flippy-70+o (root@univm25) (gcc version 11.2.0 (Ubuntu 11.2.0-16ubuntu1)) #385 SMP PREEMPT Wed Feb 23 20:45:35 CST 2022
[    0.000000] Machine model: Amlogic Meson G12A U200 Development Board
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000030000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 21 pages/cpu s47576 r8192 d30248 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 250212
[    0.000000] Kernel command line: root=UUID=61400c27-84cc-4338-b752-93cfd22694d7 rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 mac=A0:4C:0C:04:13:81
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 690496K/1016736K available (12476K kernel code, 1448K rwdata, 5200K rodata, 896K init, 853K bss, 64096K reserved, 262144K cma-reserved)
[    0.000000] random: get_random_u64 called from __kmem_cache_create+0x38/0x590 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000130] Console: colour dummy device 80x25
[    0.000421] printk: console [tty0] enabled
[    0.000457] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.000476] pid_max: default: 32768 minimum: 301
[    0.000584] LSM: Security Framework initializing
[    0.000630] SELinux:  Initializing.
[    0.000703] *** VALIDATE SELinux ***
[    0.000759] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.000778] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.000835] *** VALIDATE tmpfs ***
[    0.001243] *** VALIDATE proc ***
[    0.001445] *** VALIDATE cgroup1 ***
[    0.001458] *** VALIDATE cgroup2 ***
[    0.002115] ASID allocator initialised with 32768 entries
[    0.002202] rcu: Hierarchical SRCU implementation.
[    0.004419] EFI services will not be available.
[    0.004702] smp: Bringing up secondary CPUs ...
[    0.005210] Detected VIPT I-cache on CPU1
[    0.005256] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.005790] Detected VIPT I-cache on CPU2
[    0.005814] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006293] Detected VIPT I-cache on CPU3
[    0.006313] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006379] smp: Brought up 1 node, 4 CPUs
[    0.006434] SMP: Total of 4 processors activated.
[    0.006445] CPU features: detected: 32-bit EL0 Support
[    0.006457] CPU features: detected: CRC32 instructions
[    0.007006] CPU: All CPU(s) started at EL2
[    0.007031] alternatives: patching kernel code
[    0.007810] devtmpfs: initialized
[    0.016098] Registered cp15_barrier emulation handler
[    0.016128] Registered setend emulation handler
[    0.016318] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.016344] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.022921] xor: measuring software checksum speed
[    0.053410]    8regs     :  2301.600 MB/sec
[    0.086781]    32regs    :  2722.800 MB/sec
[    0.120153]    arm64_neon:  2103.600 MB/sec
[    0.120164] xor: using function: 32regs (2722.800 MB/sec)
[    0.120220] pinctrl core: initialized pinctrl subsystem
[    0.120724] DMI not present or invalid.
[    0.121028] NET: Registered protocol family 16
[    0.122555] DMA: preallocated 256 KiB pool for atomic allocations
[    0.122579] audit: initializing netlink subsys (disabled)
[    0.122735] audit: type=2000 audit(0.119:1): state=initialized audit_enabled=0 res=1
[    0.124067] cpuidle: using governor ladder
[    0.124269] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.124442] Serial: AMBA PL011 UART driver
[    0.140978] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.141004] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.141017] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.141029] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.142786] cryptd: max_cpu_qlen set to 1000
[    0.200320] raid6: neonx8   gen()  1535 MB/s
[    0.257003] raid6: neonx8   xor()  1437 MB/s
[    0.313752] raid6: neonx4   gen()  1475 MB/s
[    0.370465] raid6: neonx4   xor()  1382 MB/s
[    0.427202] raid6: neonx2   gen()  1130 MB/s
[    0.483929] raid6: neonx2   xor()  1137 MB/s
[    0.540653] raid6: neonx1   gen()   755 MB/s
[    0.597366] raid6: neonx1   xor()   857 MB/s
[    0.654114] raid6: int64x8  gen()  1142 MB/s
[    0.710831] raid6: int64x8  xor()   775 MB/s
[    0.767575] raid6: int64x4  gen()   978 MB/s
[    0.824288] raid6: int64x4  xor()   742 MB/s
[    0.881058] raid6: int64x2  gen()   679 MB/s
[    0.937730] raid6: int64x2  xor()   604 MB/s
[    0.994473] raid6: int64x1  gen()   442 MB/s
[    1.051166] raid6: int64x1  xor()   425 MB/s
[    1.051176] raid6: using algorithm neonx8 gen() 1535 MB/s
[    1.051186] raid6: .... xor() 1437 MB/s, rmw enabled
[    1.051196] raid6: using neon recovery algorithm
[    1.051385] fbcon: Taking over console
[    1.051911] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517
[    1.052311] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517
[    1.052411] reg-fixed-voltage regulator-vcc_3v3: Failed to register regulator: -517
[    1.052584] reg-fixed-voltage regulator-vddao_1v8: Failed to register regulator: -517
[    1.052681] VDDAO_3V3: supplied by 12V
[    1.053016] iommu: Default domain type: Translated
[    1.053279] vgaarb: loaded
[    1.053684] SCSI subsystem initialized
[    1.053869] usbcore: registered new interface driver usbfs
[    1.053910] usbcore: registered new interface driver hub
[    1.053955] usbcore: registered new device driver usb
[    1.054300] mc: Linux media interface: v0.10
[    1.054330] videodev: Linux video capture interface: v2.00
[    1.054418] pps_core: LinuxPPS API ver. 1 registered
[    1.054430] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.054461] PTP clock support registered
[    1.054624] EDAC MC: Ver: 3.0.0
[    1.055156] Advanced Linux Sound Architecture Driver Initialized.
[    1.056067] clocksource: Switched to clocksource arch_sys_counter
[    1.056086] *** VALIDATE bpf ***
[    1.056328] VFS: Disk quotas dquot_6.6.0
[    1.056391] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.056496] FS-Cache: Loaded
[    1.056506] *** VALIDATE ramfs ***
[    1.056528] *** VALIDATE hugetlbfs ***
[    1.062196] thermal_sys: Registered thermal governor 'step_wise'
[    1.062654] NET: Registered protocol family 2
[    1.062817] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.063475] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    1.063506] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.063575] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.063684] TCP: Hash tables configured (established 8192 bind 8192)
[    1.063783] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.063818] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.063968] NET: Registered protocol family 1
[    1.063998] NET: Registered protocol family 44
[    1.064015] PCI: CLS 0 bytes, default 64
[    1.064211] Trying to unpack rootfs image as initramfs...
[    2.917124] Freeing initrd memory: 6044K
[    2.917770] kvm [1]: IPA Size Limit: 40 bits
[    2.918355] kvm [1]: vgic interrupt IRQ1
[    2.918465] kvm [1]: Hyp mode initialized successfully
[    2.923188] Initialise system trusted keyrings
[    2.923326] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    2.928429] zbud: loaded
[    2.929894] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.930196] fuse: init (API version 7.31)
[    2.930275] *** VALIDATE fuse ***
[    2.930291] *** VALIDATE fuse ***
[    2.930604] SGI XFS with ACLs, security attributes, no debug enabled
[    2.946081] Key type asymmetric registered
[    2.946105] Asymmetric key parser 'x509' registered
[    2.946151] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    2.946248] io scheduler mq-deadline registered
[    2.946259] io scheduler kyber registered
[    2.946409] io scheduler bfq registered
[    2.964343] soc soc0: Amlogic Meson G12A (Unknown) Revision 28:b (70:2) Detected
[    2.965570] VDDCPU: supplied by 12V
[    2.966890] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    2.968433] Serial: AMBA driver
[    2.968779] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart
[    3.881707] printk: console [ttyAML0] enabled
[    3.893471] brd: module loaded
[    4.056093] loop: module loaded
[    4.062422] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.063346] ehci-pci: EHCI PCI platform driver
[    4.067778] ehci-platform: EHCI generic platform driver
[    4.073065] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.079052] ohci-pci: OHCI PCI platform driver
[    4.083467] ohci-platform: OHCI generic platform driver
[    4.089071] usbcore: registered new interface driver cdc_wdm
[    4.094242] usbcore: registered new interface driver usb-storage
[    4.100463] mousedev: PS/2 mouse device common for all mice
[    4.106738] meson-vrtc ff8000a8.rtc: registered as rtc0
[    4.111241] i2c /dev entries driver
[    4.124775] Synopsys Designware Multimedia Card Interface Driver
[    4.125849] meson-gx-mmc ffe05000.sd: Got CD GPIO
[    4.158194] meson-sm: secure-monitor enabled
[    4.158739] hidraw: raw HID events driver (C) Jiri Kosina
[    4.162381] usbcore: registered new interface driver usbhid
[    4.167726] usbhid: USB HID core driver
[    4.171552] exFAT: Version 1.3.0
[    4.178492] Initializing XFRM netlink socket
[    4.179610] NET: Registered protocol family 10
[    4.211484] Segment Routing with IPv6
[    4.211642] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.215677] mmc1: new high speed SDHC card at address 59b4
[    4.219864] bpfilter: Loaded bpfilter_umh pid 197
[    4.221536] mmcblk1: mmc1:59b4 USD00 29.5 GiB
[    4.225544] NET: Registered protocol family 17
[    4.234342] NET: Registered protocol family 15
[    4.238778] 8021q: 802.1Q VLAN Support v1.8
[    4.242884] Key type dns_resolver registered
[    4.247212]  mmcblk1: p1 p2
[    4.247289] Loading compiled-in X.509 certificates
[    4.254650] zswap: loaded using pool lzo/zbud
[    4.259071] Key type ._fscrypt registered
[    4.262841] Key type .fscrypt registered
[    4.267291] Btrfs loaded, crc32c=crc32c-generic
[    4.287875] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517
[    4.292328] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517
[    4.298432] VCC_3V3: supplied by VDDAO_3V3
[    4.302409] VCC_5V: supplied by 12V
[    4.305286] VDDAO_1V8: supplied by VDDAO_3V3
[    4.309506] USB_PWR_EN: supplied by VCC_5V
[    4.378492] meson-drm ff900000.vpu: Queued 3 outputs on vpu
[    4.378735] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.385004] [drm] No driver support for vblank timestamp query.
[    4.416092] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    4.420546] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    4.429392] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops)
[    4.435882] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
[    4.541492] random: fast init done
[    4.696669] [drm] kms: can't enable cloning when we probably wanted to.
[    4.975318] Console: switching to colour frame buffer device 240x67
[    5.104378] meson-drm ff900000.vpu: fb0: mesondrmfb frame buffer device
[    5.114514] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[    5.118395] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[    5.123745] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[    5.129593] meson8b-dwmac ff3f0000.ethernet: no reset control found
[    5.137345] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[    5.142878] meson8b-dwmac ff3f0000.ethernet:         DWMAC1000
[    5.148021] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[    5.155434] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[    5.162851] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[    5.168026] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[    5.175012] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[    5.181395] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[    5.187260] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[    5.193855] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    5.200982] meson8b-dwmac ff3f0000.ethernet: device MAC address 46:f0:57:d6:56:4d
[    5.210470] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[    5.213572] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[    5.222739] dwc2 ff400000.usb: ff400000.usb supply vusb_d not found, using dummy regulator
[    5.227009] dwc2 ff400000.usb: ff400000.usb supply vusb_a not found, using dummy regulator
[    5.236085] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    5.243163] dwc3 ff500000.usb: Failed to get clk 'ref': -2
[    5.247895] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.253960] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    5.260695] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[    5.270687] xhci-hcd xhci-hcd.3.auto: irq 29, io mem 0xff500000
[    5.276025] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    5.284696] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.291103] usb usb1: Product: xHCI Host Controller
[    5.296672] usb usb1: Manufacturer: Linux 5.4.181-flippy-70+o xhci-hcd
[    5.302400] usb usb1: SerialNumber: xhci-hcd.3.auto
[    5.307512] hub 1-0:1.0: USB hub found
[    5.310961] hub 1-0:1.0: 2 ports detected
[    5.315107] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.320440] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    5.327944] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    5.334435] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.342485] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[    5.350615] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.357773] usb usb2: Product: xHCI Host Controller
[    5.362603] usb usb2: Manufacturer: Linux 5.4.181-flippy-70+o xhci-hcd
[    5.369071] usb usb2: SerialNumber: xhci-hcd.3.auto
[    5.374144] hub 2-0:1.0: USB hub found
[    5.377702] hub 2-0:1.0: 1 port detected
[    5.382971] FLASH_1V8: supplied by VCC_3V3
[    5.386719] VCC_1V8: supplied by VCC_3V3
[    5.397708] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[    5.425924] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:05 UTC (5)
[    5.433469] ALSA device list:
[    5.438109]   No soundcards found.
[    5.443178] Freeing unused kernel memory: 896K
[    5.456143] Run /init as init process
[    5.538762] mmc2: new HS200 MMC card at address 0001
[    5.544493] mmcblk2: mmc2:0001 SPeMMC 7.22 GiB
[    5.548478] mmcblk2boot0: mmc2:0001 SPeMMC partition 1 4.00 MiB
[    5.554001] mmcblk2boot1: mmc2:0001 SPeMMC partition 2 4.00 MiB
[    5.558984] mmcblk2rpmb: mmc2:0001 SPeMMC partition 3 4.00 MiB, chardev (239:0)
[    5.599449] usb 1-1: new full-speed USB device number 2 using xhci-hcd
[    5.747653] usb 1-1: New USB device found, idVendor=413c, idProduct=301c, bcdDevice= 2.28
[    5.753627] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.762408] usb 1-1: Product: Dell Universal Receiver
[    5.765805] usb 1-1: Manufacturer: Dell Computer Corp
[    5.789514] input: Dell Computer Corp Dell Universal Receiver as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.0/0003:413C:301C.0001/input/input0
[    5.860049] hid-generic 0003:413C:301C.0001: input,hidraw0: USB HID v1.11 Keyboard [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input0
[    5.880124] input: Dell Computer Corp Dell Universal Receiver Mouse as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input1
[    5.898028] input: Dell Computer Corp Dell Universal Receiver Consumer Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input2
[    5.973773] input: Dell Computer Corp Dell Universal Receiver System Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input3
[    5.992089] hid-generic 0003:413C:301C.0002: input,hidraw1: USB HID v1.11 Mouse [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input1
[    6.010823] hid-generic 0003:413C:301C.0003: hiddev96,hidraw2: USB HID v1.11 Device [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input2
[    6.380697] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
[    7.176688] systemd[1]: System time before build time, advancing clock.
[    7.287735] systemd[1]: systemd 245.4-4ubuntu3.15 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[    7.314407] systemd[1]: Detected architecture arm64.
[    7.385836] systemd[1]: Set hostname to <armbian>.
[    8.179691] random: systemd: uninitialized urandom read (16 bytes read)
[    8.189552] systemd[1]: Created slice system-modprobe.slice.
[    8.201265] random: systemd: uninitialized urandom read (16 bytes read)
[    8.208493] systemd[1]: Created slice system-serial\x2dgetty.slice.
[    8.218936] random: systemd: uninitialized urandom read (16 bytes read)
[    8.225492] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[    8.236813] systemd[1]: Created slice User and Session Slice.
[    8.246710] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[    8.259296] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    8.272447] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    8.286511] systemd[1]: Reached target Local Encrypted Volumes.
[    8.297105] systemd[1]: Reached target Slices.
[    8.307302] systemd[1]: Reached target Swap.
[    8.317532] systemd[1]: Reached target System Time Set.
[    8.341730] systemd[1]: Listening on RPCbind Server Activation Socket.
[    8.354439] systemd[1]: Listening on Syslog Socket.
[    8.365402] systemd[1]: Listening on fsck to fsckd communication Socket.
[    8.377261] systemd[1]: Listening on initctl Compatibility Named Pipe.
[    8.389552] systemd[1]: Listening on Journal Audit Socket.
[    8.400755] systemd[1]: Listening on Journal Socket (/dev/log).
[    8.412393] systemd[1]: Listening on Journal Socket.
[    8.423724] systemd[1]: Listening on udev Control Socket.
[    8.434897] systemd[1]: Listening on udev Kernel Socket.
[    8.448700] systemd[1]: Mounting Huge Pages File System...
[    8.462650] systemd[1]: Mounting POSIX Message Queue File System...
[    8.476492] systemd[1]: Mounting RPC Pipe File System...
[    8.489694] systemd[1]: Mounting Kernel Debug File System...
[    8.499867] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[    8.522133] systemd[1]: Starting Restore / save the current clock...
[    8.528944] RPC: Registered named UNIX socket transport module.
[    8.528948] RPC: Registered udp transport module.
[    8.528949] RPC: Registered tcp transport module.
[    8.528951] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    8.557201] systemd[1]: Starting Set the console keyboard layout...
[    8.571214] systemd[1]: Starting Create list of static device nodes for the current kernel...
[    8.583850] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
[    8.586968] systemd[1]: Started Nameserver information manager.
[    8.602266] systemd[1]: Reached target Network (Pre).
[    8.613443] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    8.621623] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    8.635482] systemd[1]: Starting Load Kernel Modules...
[    8.648318] systemd[1]: Starting Remount Root and Kernel File Systems...
[    8.662166] systemd[1]: Starting udev Coldplug all Devices...
[    8.674335] EXT4-fs (mmcblk1p2): re-mounted. Opts: errors=remount-ro
[    8.676775] systemd[1]: Mounted Huge Pages File System.
[    8.685019] usbcore: registered new interface driver r8152
[    8.696823] systemd[1]: Mounted POSIX Message Queue File System.
[    8.707051] systemd[1]: Mounted RPC Pipe File System.
[    8.714243] usbcore: registered new interface driver ax88179_178a
[    8.721342] systemd[1]: Mounted Kernel Debug File System.
[    8.732393] systemd[1]: Finished Restore / save the current clock.
[    8.744000] systemd[1]: Finished Create list of static device nodes for the current kernel.
[    8.761120] systemd[1]: Finished Load Kernel Modules.
[    8.772363] systemd[1]: Finished Remount Root and Kernel File Systems.
[    8.787314] systemd[1]: Mounting FUSE Control File System...
[    8.800998] systemd[1]: Mounting Kernel Configuration File System...
[    8.814608] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    8.822935] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[    8.834614] systemd[1]: Starting Load/Save Random Seed...
[    8.848981] systemd[1]: Starting Apply Kernel Variables...
[    8.862459] systemd[1]: Starting Create System Users...
[    8.876454] systemd[1]: Finished Set the console keyboard layout.
[    8.889166] systemd[1]: Mounted FUSE Control File System.
[    8.899731] systemd[1]: Mounted Kernel Configuration File System.
[    8.912032] systemd[1]: Finished Apply Kernel Variables.
[    9.007757] systemd[1]: Finished udev Coldplug all Devices.
[    9.028640] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[    9.067640] systemd[1]: Finished Create System Users.
[    9.081733] systemd[1]: Starting Create Static Device Nodes in /dev...
[    9.121584] systemd[1]: Finished Create Static Device Nodes in /dev.
[    9.133335] systemd[1]: Reached target Local File Systems (Pre).
[    9.147722] systemd[1]: Mounting /var/tmp...
[    9.161849] systemd[1]: Starting udev Kernel Device Manager...
[    9.176654] systemd[1]: Mounted /var/tmp.
[    9.299891] systemd[1]: Started udev Kernel Device Manager.
[    9.556851] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[    9.588984] Registered IR keymap rc-cec
[    9.593867] rc rc0: dw_hdmi as /devices/platform/soc/ff600000.bus/ff600000.hdmi-tx/rc/rc0
[    9.609712] input: dw_hdmi as /devices/platform/soc/ff600000.bus/ff600000.hdmi-tx/rc/rc0/input4
[    9.620499] systemd[1]: Found device /dev/ttyAML0.
[    9.625567] Registered IR keymap rc-empty
[    9.625654] rc rc1: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1
[    9.634415] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[    9.634552] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1/input5
[    9.637687] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present!
[    9.639032] meson-ir ff808000.ir: receiver initialized
[    9.644067] Registered IR keymap rc-cec
[    9.644215] rc rc2: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc2
[    9.644329] input: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc2/input6
[    9.710743] axg-sound-card sound: snd-soc-dummy-dai <-> ff6421c0.audio-controller mapping ok
[    9.720233] axg-sound-card sound: snd-soc-dummy-dai <-> ff642200.audio-controller mapping ok
[    9.730503] axg-sound-card sound: snd-soc-dummy-dai <-> ff642240.audio-controller mapping ok
[    9.748656] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[    9.762032] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[    9.762086] axg-sound-card sound: I2S IN B <-> TDM Pad mapping ok
[    9.769963] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[    9.780070] axg-sound-card sound: snd-soc-dummy-dai <-> TDM Loopback mapping ok
[    9.792949] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    9.795533] axg-sound-card sound: multicodec <-> ff642480.audio-controller mapping ok
[    9.803469] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[    9.809281] axg-sound-card sound: SPDIF IN B <-> ff642680.audio-controller mapping ok
[    9.821419] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[    9.825529] axg-sound-card sound: i2s-hifi <-> I2S OUT mapping ok
[    9.840627] axg-sound-card sound: ASoC: no DMI vendor name!
[    9.974567] systemd[1]: Found device /dev/disk/by-label/BOOT.
[    9.993448] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[   10.037531] systemd[1]: Started File System Check Daemon to report status.
[   10.090302] systemd[1]: Found device /sys/subsystem/net/devices/eth0.
[   10.210677] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   10.211059] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   10.211390] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   10.211455] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   10.211547] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   10.211622] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   10.222883] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[   10.321194] systemd[1]: Mounting /boot...
[   10.359840] systemd[1]: Mounted /boot.
[   10.371355] systemd[1]: Reached target Local File Systems.
[   10.384372] systemd[1]: Starting Armbian ZRAM config...
[   10.399889] systemd[1]: Starting Set console font and keymap...
[   10.414914] systemd[1]: Started ifup for eth0.
[   10.432113] systemd[1]: Starting Preprocess NFS configuration...
[   10.451121] systemd[1]: Starting Mark the need to relabel after reboot...
[   10.465416] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   10.477193] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[   10.490421] systemd[1]: nfs-config.service: Succeeded.
[   10.497294] systemd[1]: Finished Preprocess NFS configuration.
[   10.510005] systemd[1]: Finished Mark the need to relabel after reboot.
[   10.525294] systemd[1]: Starting Raise network interfaces...
[   10.538205] systemd[1]: Condition check resulted in RPC security service for NFS client and server being skipped.
[   10.547881] systemd[1]: Reached target NFS client services.
[   10.710449] zram: Added device: zram0
[   10.715875] zram: Added device: zram1
[   10.721083] zram: Added device: zram2
[   10.849445] crng init done
[   10.854077] random: 7 urandom warning(s) missed due to ratelimiting
[   10.945922] systemd[1]: Finished Load/Save Random Seed.
[   10.957207] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[   10.972605] zram0: detected capacity change from 0 to 491307008
[   11.079474] Adding 479788k swap on /dev/zram0.  Priority:5 extents:1 across:479788k SSFS
[   11.179450] zram1: detected capacity change from 0 to 52428800
[   11.186662] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   11.191932] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   11.244776] zram2: detected capacity change from 0 to 491307008
[   11.278279] EXT4-fs (zram2): mounted filesystem without journal. Opts: discard
[   11.284518] ext4 filesystem being mounted at /var/tmp supports timestamps until 2038 (0x7fffffff)
[   11.309978] systemd[1]: Finished Armbian ZRAM config.
[   11.323712] systemd[1]: Starting Armbian memory supported logging...
[   11.565675] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[   11.571856] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   13.555600] systemd[1]: Finished Armbian memory supported logging.
[   13.570581] systemd[1]: Starting Journal Service...
[   13.719506] systemd[1]: Started Journal Service.
[   13.759958] systemd-journald[711]: Received client request to flush runtime journal.
[   14.793728] [drm] kms: can't enable cloning when we probably wanted to.
[   17.900003] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   17.904742] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   18.079977] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   18.084601] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   18.176654] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   18.181267] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   18.270016] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   18.274681] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   18.363319] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   18.367945] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

Calmact · 2022-03-01T17:40:28Z

armbian with kernel 5.4 is bootable from USB,
but also without 100M eth0 ethernet

G12A:BL:0253b8:61aa2d;FEAT:E0F93180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0;
                                                                       bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02

L0:00000000
L1:00000701
L2:00008267
L3:04000000
S1:00000000
B2:00002000
B1:e0f93180

TE: 107222

BL2 Built : 14:02:05, Nov 23 2020. g12a g966c864 - gongwei.chen@droid11-sz

Board ID = 4
Set cpu clk to 24M
Set clk81 to 24M
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
board id: 4
Load FIP HDR DDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
PIEI prepare done
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
result: 255
Cfg max: 12, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe

LPDDR4_PHY_V_0_1_22-Built : 15:59:30, May 25 2020. g12a gb6bfa83 - gongwei.chen@droid11-sz
ddr clk to 1176MHz

dmc_version 0000
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of Write leveling coarse delay
INFO : End of read delay center optimization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!

soc_vref_reg_value 0x 00000027 00000027 00000025 00000026 00000026 00000027 00000026 00000026 00000025 00000025 00000027 00000026 00000026 00000027 00000025 00000027 00000024 00000025 00000023 00000024 00000026 00000027 00000026 00000024 00000027 00000025 00000026 00000025 00000025 00000026 00000025 00000025 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
 dram_vref_reg_value 0x 0000005f
2D training succeed
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 00c0002cDDR size: 2048MB
cs0 DataBus test pass
cs0 AddrBus test pass

non-sec scramble use zero key
ddr scramble enabled

100bdlr_step_size ps== 438
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d6a00, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
[Image: g12a_v1.1.3394-7d43064d5 2020-05-07 15:37:06 gongwei.chen@droid11-sz]
OPS=0x70
ring efuse init
28 0b 70 00 01 35 2c 00 00 01 32 38 30 4b 41 50
[0.014262 Inits done]
secure task start!
high task start!
low task start!
boot bl31
NOTICE:  BL31: v1.3(release):9d705ef56-dirty
NOTICE:  BL31: Built : 19:18:02, Jul 28 2021
NOTICE:  BL31: G12A normal boot!
NOTICE:  BL31: BL33 decompress pass
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01 (Sep 26 2021 - 14:35:31)

DRAM:  2 GiB
Relocation Offset is: 76e45000
mmu cfg end: 0x80000000
mmu cfg end: 0x80000000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 0000000077f3be68
gpio: pin GPIOAO_9 (gpio 9) value is 0
NAND:  get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
get_sys_clk_rate_mtd() 292, clock setting 200!
bus cycle0: 6,timing: 7
NAND device id: 0 ff ff ff ff ff
No NAND device found!!!
nand init failed: -6
MMC:   aml_priv->desc_buf = 0x0000000073e35d90
aml_priv->desc_buf = 0x0000000073e380d0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, cmd->cmdarg=0x1aa, status=0x1ff2800
emmc/sd response timeout, cmd55, cmd->cmdarg=0x0, status=0x1ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 40000000
[set_emmc_calc_fixed_adj][875]find fixed adj_delay=20
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
start dts,buffer=0000000073e3a920,dt_addr=0000000073e3a920
get_partition_from_dts() 92: ret 0
      Amlogic multi-dtb tool
      Single dtb detected
parts: 21
00:      logo   0000000000800000 1
01:  recovery   0000000001800000 1
02:      misc   0000000000800000 1
03:      dtbo   0000000000800000 1
04:  cri_data   0000000000800000 2
05:     param   0000000001000000 2
06:      boot   0000000001000000 1
set has_boot_slot = 0
07:       rsv   0000000001000000 1
08:  metadata   0000000001000000 1
09:    vbmeta   0000000000200000 1
10:       tee   0000000002000000 1
11:    vendor   0000000014000000 1
12:     skmac   0000000000400000 1
13:       odm   0000000001000000 1
14:    system   0000000050000000 1
15:   product   0000000008000000 1
16:       ctc   0000000010000000 1
17:   skparam   0000000001000000 2
18:  skbackup   0000000030000000 2
19:     cache   0000000040000000 2
20:      data   ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
_verify_dtb_checksum()-3476: calc 43030b8b, store 43030b8b
dtb_read()-3691: total valid 2
update_old_dtb()-3672: do nothing
      Amlogic multi-dtb tool
      GZIP format, decompress...
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 3 dtbs.
        aml_dt soc: g12a platform: u212 variant: 2g
        dtb 0 soc: g12a   plat: u212   vari: 1g
        dtb 1 soc: g12a   plat: u212   vari: 2g
        dtb 2 soc: sm1   plat: ac213   vari: 2g
      Find match dtb: 1
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
vpu: driver version: v20190313
vpu: detect chip type: 8
vpu: clk_level default: 7(666667000Hz), max: 7(666667000Hz)
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set_vpu_clk
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: set_vpu_clk finish
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
hdr_func 4, hdr_process_select 0x1
cvbs: cpuid:0x28
vdac_gsw_init: 0x0
cvbs: find clk_path: 0x0
cvbs: find performance_pal config
cvbs: find performance_ntsc config
aml_config_dtb 637
aml_config_dtb 667
co_phase = <0x00000003>
caps2 = "MMC_CAP2_HS200"
f_max = <0x02faf080>
status = "disabled"
status = "okay"
wipe_data=successful
wipe_cache=successful
upgrade_step=2
reboot_mode:::: cold_boot
ext4logoLoadCmd=ext4load mmc 1:${logoPart} ${logoLoadAddr} ${ext4LogoPath}
** File not found /logo_files/bootup.bmp **
Err imgread(L815):Fail in load logo cmd
logo part bootup
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
[OSD]osd_hw.free_dst_data: 0,3839,0,2159
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[2160p60hz] is invalid
vpp: vpp_matrix_update: 2
set hdmitx VIC = 97
aml_audio_init
config HPLL = 5940000 frac_rate = 0
HPLL: 0x3b3a04f7
HPLL: 0x1b3a04f7
HPLLv1: 0xdb3a04f7
config HPLL done
j = 11  vid_clk_div = 1
hdmitx: set enc for VIC: 353
hdmitx phy setting done
rx version is 1.4 or below  div=10
hdmtix: set audio
hdmi_tx_set: save mode: 2160p60hz, attr: 420,8bit, hdmichecksum: <NULL>
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
hdr_packet
vpp: hdr_policy = 2
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
time_out = 493e0
key[0] = 66994cb3
key[1] = 6699fd01
key[2] = 6699dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
time_out = 0
key[0] = 3ec14cb3
key[1] = 3ec1fd01
key[2] = 3ec1dd22
irkey - irkey <timeout> <key1> ...<keyN> - maximum value of N: 10

Usage:
irkey - No additional help available.
Command: bcb uboot-command
Start read misc partition datas!
BCB hasn't any datas,exit!
InUsbBurn
wait for phy ready count is 0
noSof
sof timeout, reset usb phy tuning
rebootmode=cold_boot
Saving Environment to aml-storage...
mmc env offset: 0x6c00000
Writing to MMC(1)... done
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card out
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 3000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices... init_part() 282: PART_TYPE_DOS
1 Storage Device(s) found
reading s905_autoscript
1654 bytes read in 33 ms (48.8 KiB/s)
## Executing script at 01020000
start amlogic old u-boot
## Error: "bootfromsd" not defined
card out
** Bad device mmc 0 **
reading boot_android
** Unable to read file boot_android **
card out
** Bad device mmc 0 **
reading u-boot.ext
** Unable to read file u-boot.ext **
card out
** Bad device mmc 0 **
start test usb
reading uEnv.txt
336 bytes read in 47 ms (6.8 KiB/s)
mac=A0:4C:0C:04:13:81
reading /zImage
20685312 bytes read in 630 ms (31.3 MiB/s)
reading /uInitrd
6190008 bytes read in 227 ms (26 MiB/s)
reading /dtb/amlogic/meson-g12a-u200.dtb
45932 bytes read in 51 ms (878.9 KiB/s)
## Error: "aadmac" not defined
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] fdt get prop fail.
## Loading init Ramdisk from Legacy Image at 13000000 ...
   Image Name:   uInitrd
   Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
   Data Size:    6189944 Bytes = 5.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
[store]Is good fdt check header, no need decrypt!
active_slot is normal
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
## Flattened Device Tree blob at 01000000
   Booting using the fdt blob at 0x1000000
find 1 dtbos
No androidboot.dtbo_idx configured
And no dtbos will be applied
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] fdt get prop fail.
   Loading Ramdisk to 7384b000, end 73e32378 ... OK
   Loading Device Tree to 000000001fff1000, end 000000001ffff421 ... OK
fdt_fixup_memory_banks, reg:000000001fffb2f8
DTS already have 'reg' property

Starting kernel ...

uboot time: 7305723 us
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 5.4.181-flippy-70+o (root@univm25) (gcc version 11.2.0 (Ubuntu 11.2.0-16ubuntu1)) #385 SMP PREEMPT Wed Feb 23 20:45:35 CST 2022
[    0.000000] Machine model: Amlogic Meson G12A U200 Development Board
[    0.000000] efi: Getting EFI parameters from FDT:
[    0.000000] efi: UEFI not found.
[    0.000000] Reserved memory: created CMA memory pool at 0x0000000030000000, size 256 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.1
[    0.000000] percpu: Embedded 21 pages/cpu s47576 r8192 d30248 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: ARM erratum 845719
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 250212
[    0.000000] Kernel command line: root=UUID=61400c27-84cc-4338-b752-93cfd22694d7 rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 mac=A0:4C:0C:04:13:81
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 690496K/1016736K available (12476K kernel code, 1448K rwdata, 5200K rodata, 896K init, 853K bss, 64096K reserved, 262144K cma-reserved)
[    0.000000] random: get_random_u64 called from __kmem_cache_create+0x38/0x590 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000131] Console: colour dummy device 80x25
[    0.000423] printk: console [tty0] enabled
[    0.000460] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.000479] pid_max: default: 32768 minimum: 301
[    0.000586] LSM: Security Framework initializing
[    0.000632] SELinux:  Initializing.
[    0.000704] *** VALIDATE SELinux ***
[    0.000759] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.000778] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.000835] *** VALIDATE tmpfs ***
[    0.001243] *** VALIDATE proc ***
[    0.001448] *** VALIDATE cgroup1 ***
[    0.001461] *** VALIDATE cgroup2 ***
[    0.002118] ASID allocator initialised with 32768 entries
[    0.002205] rcu: Hierarchical SRCU implementation.
[    0.004437] EFI services will not be available.
[    0.004720] smp: Bringing up secondary CPUs ...
[    0.005228] Detected VIPT I-cache on CPU1
[    0.005273] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.005807] Detected VIPT I-cache on CPU2
[    0.005830] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.006308] Detected VIPT I-cache on CPU3
[    0.006328] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.006395] smp: Brought up 1 node, 4 CPUs
[    0.006451] SMP: Total of 4 processors activated.
[    0.006462] CPU features: detected: 32-bit EL0 Support
[    0.006473] CPU features: detected: CRC32 instructions
[    0.007022] CPU: All CPU(s) started at EL2
[    0.007047] alternatives: patching kernel code
[    0.007821] devtmpfs: initialized
[    0.016119] Registered cp15_barrier emulation handler
[    0.016150] Registered setend emulation handler
[    0.016337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.016363] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.022995] xor: measuring software checksum speed
[    0.053411]    8regs     :  2301.600 MB/sec
[    0.086783]    32regs    :  2722.800 MB/sec
[    0.120155]    arm64_neon:  2112.000 MB/sec
[    0.120166] xor: using function: 32regs (2722.800 MB/sec)
[    0.120223] pinctrl core: initialized pinctrl subsystem
[    0.120730] DMI not present or invalid.
[    0.121029] NET: Registered protocol family 16
[    0.122576] DMA: preallocated 256 KiB pool for atomic allocations
[    0.122611] audit: initializing netlink subsys (disabled)
[    0.122756] audit: type=2000 audit(0.119:1): state=initialized audit_enabled=0 res=1
[    0.124089] cpuidle: using governor ladder
[    0.124290] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.124463] Serial: AMBA PL011 UART driver
[    0.141001] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[    0.141027] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[    0.141039] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.141052] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[    0.142811] cryptd: max_cpu_qlen set to 1000
[    0.203652] raid6: neonx8   gen()  1535 MB/s
[    0.260339] raid6: neonx8   xor()  1438 MB/s
[    0.317084] raid6: neonx4   gen()  1475 MB/s
[    0.373797] raid6: neonx4   xor()  1382 MB/s
[    0.430527] raid6: neonx2   gen()  1129 MB/s
[    0.487259] raid6: neonx2   xor()  1137 MB/s
[    0.543998] raid6: neonx1   gen()   754 MB/s
[    0.600695] raid6: neonx1   xor()   857 MB/s
[    0.657450] raid6: int64x8  gen()  1142 MB/s
[    0.714166] raid6: int64x8  xor()   776 MB/s
[    0.770919] raid6: int64x4  gen()   978 MB/s
[    0.827628] raid6: int64x4  xor()   742 MB/s
[    0.884384] raid6: int64x2  gen()   679 MB/s
[    0.941067] raid6: int64x2  xor()   604 MB/s
[    0.997771] raid6: int64x1  gen()   442 MB/s
[    1.054516] raid6: int64x1  xor()   425 MB/s
[    1.054526] raid6: using algorithm neonx8 gen() 1535 MB/s
[    1.054537] raid6: .... xor() 1438 MB/s, rmw enabled
[    1.054547] raid6: using neon recovery algorithm
[    1.054736] fbcon: Taking over console
[    1.055261] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517
[    1.055659] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517
[    1.055760] reg-fixed-voltage regulator-vcc_3v3: Failed to register regulator: -517
[    1.055934] reg-fixed-voltage regulator-vddao_1v8: Failed to register regulator: -517
[    1.056033] VDDAO_3V3: supplied by 12V
[    1.056365] iommu: Default domain type: Translated
[    1.056628] vgaarb: loaded
[    1.057034] SCSI subsystem initialized
[    1.057219] usbcore: registered new interface driver usbfs
[    1.057261] usbcore: registered new interface driver hub
[    1.057304] usbcore: registered new device driver usb
[    1.057653] mc: Linux media interface: v0.10
[    1.057684] videodev: Linux video capture interface: v2.00
[    1.057772] pps_core: LinuxPPS API ver. 1 registered
[    1.057783] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.057814] PTP clock support registered
[    1.057976] EDAC MC: Ver: 3.0.0
[    1.058510] Advanced Linux Sound Architecture Driver Initialized.
[    1.059420] clocksource: Switched to clocksource arch_sys_counter
[    1.059440] *** VALIDATE bpf ***
[    1.059682] VFS: Disk quotas dquot_6.6.0
[    1.059746] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.059853] FS-Cache: Loaded
[    1.059863] *** VALIDATE ramfs ***
[    1.059884] *** VALIDATE hugetlbfs ***
[    1.065564] thermal_sys: Registered thermal governor 'step_wise'
[    1.066025] NET: Registered protocol family 2
[    1.066186] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.066847] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    1.066879] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.066948] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.067069] TCP: Hash tables configured (established 8192 bind 8192)
[    1.067173] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.067207] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.067357] NET: Registered protocol family 1
[    1.067388] NET: Registered protocol family 44
[    1.067405] PCI: CLS 0 bytes, default 64
[    1.067601] Trying to unpack rootfs image as initramfs...
[    2.920553] Freeing initrd memory: 6044K
[    2.921205] kvm [1]: IPA Size Limit: 40 bits
[    2.921788] kvm [1]: vgic interrupt IRQ1
[    2.921902] kvm [1]: Hyp mode initialized successfully
[    2.926897] Initialise system trusted keyrings
[    2.927034] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    2.932138] zbud: loaded
[    2.933600] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.933917] fuse: init (API version 7.31)
[    2.933998] *** VALIDATE fuse ***
[    2.934014] *** VALIDATE fuse ***
[    2.934327] SGI XFS with ACLs, security attributes, no debug enabled
[    2.949331] Key type asymmetric registered
[    2.949354] Asymmetric key parser 'x509' registered
[    2.949398] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[    2.949509] io scheduler mq-deadline registered
[    2.949521] io scheduler kyber registered
[    2.949659] io scheduler bfq registered
[    2.967644] soc soc0: Amlogic Meson G12A (Unknown) Revision 28:b (70:2) Detected
[    2.968858] VDDCPU: supplied by 12V
[    2.970134] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
[    2.971654] Serial: AMBA driver
[    2.971993] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 14, base_baud = 1500000) is a meson_uart
[    3.884924] printk: console [ttyAML0] enabled
[    3.896658] brd: module loaded
[    4.062779] loop: module loaded
[    4.069168] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.070096] ehci-pci: EHCI PCI platform driver
[    4.074520] ehci-platform: EHCI generic platform driver
[    4.079807] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.085778] ohci-pci: OHCI PCI platform driver
[    4.090198] ohci-platform: OHCI generic platform driver
[    4.095813] usbcore: registered new interface driver cdc_wdm
[    4.100986] usbcore: registered new interface driver usb-storage
[    4.107208] mousedev: PS/2 mouse device common for all mice
[    4.113466] meson-vrtc ff8000a8.rtc: registered as rtc0
[    4.117985] i2c /dev entries driver
[    4.131968] Synopsys Designware Multimedia Card Interface Driver
[    4.133047] meson-gx-mmc ffe05000.sd: Got CD GPIO
[    4.163560] meson-sm: secure-monitor enabled
[    4.163989] hidraw: raw HID events driver (C) Jiri Kosina
[    4.167641] usbcore: registered new interface driver usbhid
[    4.173076] usbhid: USB HID core driver
[    4.176869] exFAT: Version 1.3.0
[    4.182796] Initializing XFRM netlink socket
[    4.184622] NET: Registered protocol family 10
[    4.214226] Segment Routing with IPv6
[    4.214411] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    4.220515] bpfilter: Loaded bpfilter_umh pid 197
[    4.222848] NET: Registered protocol family 17
[    4.227257] NET: Registered protocol family 15
[    4.231681] 8021q: 802.1Q VLAN Support v1.8
[    4.235769] Key type dns_resolver registered
[    4.240220] Loading compiled-in X.509 certificates
[    4.244797] zswap: loaded using pool lzo/zbud
[    4.249226] Key type ._fscrypt registered
[    4.252990] Key type .fscrypt registered
[    4.257456] Btrfs loaded, crc32c=crc32c-generic
[    4.278033] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517
[    4.283688] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517
[    4.288807] VCC_3V3: supplied by VDDAO_3V3
[    4.294523] VCC_5V: supplied by 12V
[    4.295424] VDDAO_1V8: supplied by VDDAO_3V3
[    4.299658] USB_PWR_EN: supplied by VCC_5V
[    4.381947] meson-drm ff900000.vpu: Queued 3 outputs on vpu
[    4.382204] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.388459] [drm] No driver support for vblank timestamp query.
[    4.422790] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
[    4.427307] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver
[    4.435425] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops)
[    4.444825] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 0
[    4.567378] random: fast init done
[    4.713819] [drm] kms: can't enable cloning when we probably wanted to.
[    5.001985] Console: switching to colour frame buffer device 240x67
[    5.125793] meson-drm ff900000.vpu: fb0: mesondrmfb frame buffer device
[    5.135924] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found
[    5.139860] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found
[    5.145152] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock
[    5.150988] meson8b-dwmac ff3f0000.ethernet: no reset control found
[    5.158832] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37
[    5.164268] meson8b-dwmac ff3f0000.ethernet:         DWMAC1000
[    5.169444] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported
[    5.176850] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported
[    5.184267] meson8b-dwmac ff3f0000.ethernet: COE Type 2
[    5.189446] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported
[    5.196428] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported
[    5.202814] meson8b-dwmac ff3f0000.ethernet: Normal descriptors
[    5.208676] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled
[    5.215286] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    5.222397] meson8b-dwmac ff3f0000.ethernet: device MAC address d2:db:34:f6:b1:c7
[    5.231874] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2
[    5.234999] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1
[    5.244157] dwc2 ff400000.usb: ff400000.usb supply vusb_d not found, using dummy regulator
[    5.248409] dwc2 ff400000.usb: ff400000.usb supply vusb_a not found, using dummy regulator
[    5.257528] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM
[    5.264539] dwc3 ff500000.usb: Failed to get clk 'ref': -2
[    5.269334] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.275382] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 1
[    5.282109] xhci-hcd xhci-hcd.3.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010
[    5.292109] xhci-hcd xhci-hcd.3.auto: irq 29, io mem 0xff500000
[    5.297439] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[    5.306117] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.312518] usb usb1: Product: xHCI Host Controller
[    5.318089] usb usb1: Manufacturer: Linux 5.4.181-flippy-70+o xhci-hcd
[    5.323819] usb usb1: SerialNumber: xhci-hcd.3.auto
[    5.328928] hub 1-0:1.0: USB hub found
[    5.332374] hub 1-0:1.0: 2 ports detected
[    5.336533] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    5.341853] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 2
[    5.349354] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    5.355864] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    5.363902] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.04
[    5.372034] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    5.379188] usb usb2: Product: xHCI Host Controller
[    5.384018] usb usb2: Manufacturer: Linux 5.4.181-flippy-70+o xhci-hcd
[    5.390489] usb usb2: SerialNumber: xhci-hcd.3.auto
[    5.395580] hub 2-0:1.0: USB hub found
[    5.399139] hub 2-0:1.0: 1 port detected
[    5.404368] FLASH_1V8: supplied by VCC_3V3
[    5.408121] VCC_1V8: supplied by VCC_3V3
[    5.419141] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq
[    5.449274] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:05 UTC (5)
[    5.456658] ALSA device list:
[    5.462551]   No soundcards found.
[    5.466950] Freeing unused kernel memory: 896K
[    5.472781] Run /init as init process
[    5.540075] mmc2: new HS200 MMC card at address 0001
[    5.544934] mmcblk2: mmc2:0001 SPeMMC 7.22 GiB
[    5.550249] mmcblk2boot0: mmc2:0001 SPeMMC partition 1 4.00 MiB
[    5.554212] mmcblk2boot1: mmc2:0001 SPeMMC partition 2 4.00 MiB
[    5.560025] mmcblk2rpmb: mmc2:0001 SPeMMC partition 3 4.00 MiB, chardev (239:0)
[    5.622803] usb 1-1: new full-speed USB device number 2 using xhci-hcd
[    5.770299] usb 1-1: New USB device found, idVendor=413c, idProduct=301c, bcdDevice= 2.28
[    5.776241] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.783786] usb 1-1: Product: Dell Universal Receiver
[    5.788328] usb 1-1: Manufacturer: Dell Computer Corp
[    5.815981] input: Dell Computer Corp Dell Universal Receiver as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.0/0003:413C:301C.0001/input/input0
[    5.887077] hid-generic 0003:413C:301C.0001: input,hidraw0: USB HID v1.11 Keyboard [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input0
[    5.908995] input: Dell Computer Corp Dell Universal Receiver Mouse as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input1
[    5.929340] input: Dell Computer Corp Dell Universal Receiver Consumer Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input2
[    6.004643] input: Dell Computer Corp Dell Universal Receiver System Control as /devices/platform/soc/ffe09000.usb/ff500000.usb/xhci-hcd.3.auto/usb1/1-1/1-1:1.1/0003:413C:301C.0002/input/input3
[    6.023620] hid-generic 0003:413C:301C.0002: input,hidraw1: USB HID v1.11 Mouse [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input1
[    6.045250] hid-generic 0003:413C:301C.0003: hiddev96,hidraw2: USB HID v1.11 Device [Dell Computer Corp Dell Universal Receiver] on usb-xhci-hcd.3.auto-1/input2
[    6.184320] usb 1-2: new high-speed USB device number 3 using xhci-hcd
[    6.345746] usb 1-2: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 1.10
[    6.426881] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    6.461003] usb 1-2: Product: DataTraveler 3.0
[    6.476289] usb 1-2: Manufacturer: Kingston
[    6.486135] usb 1-2: SerialNumber: AC220B280C75B041293F58E8
[    6.497828] usb-storage 1-2:1.0: USB Mass Storage device detected
[    6.506853] scsi host0: usb-storage 1-2:1.0
[    7.523887] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6
[    7.537183] sd 0:0:0:0: [sda] 30277632 512-byte logical blocks: (15.5 GB/14.4 GiB)
[    7.563035] sd 0:0:0:0: [sda] Write Protect is off
[    7.585612] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    7.727423]  sda: sda1 sda2
[    7.755243] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   10.200633] EXT4-fs (sda2): recovery complete
[   10.213919] EXT4-fs (sda2): mounted filesystem with writeback data mode. Opts: data=writeback
[   10.706929] systemd[1]: System time before build time, advancing clock.
[   10.805473] systemd[1]: systemd 245.4-4ubuntu3.15 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid)
[   10.836906] systemd[1]: Detected architecture arm64.
[   10.911663] systemd[1]: Set hostname to <armbian>.
[   11.525673] random: systemd: uninitialized urandom read (16 bytes read)
[   11.534261] systemd[1]: Created slice system-modprobe.slice.
[   11.545936] random: systemd: uninitialized urandom read (16 bytes read)
[   11.552940] systemd[1]: Created slice system-serial\x2dgetty.slice.
[   11.563911] random: systemd: uninitialized urandom read (16 bytes read)
[   11.570697] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[   11.582344] systemd[1]: Created slice User and Session Slice.
[   11.592562] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   11.605322] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   11.618707] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   11.633285] systemd[1]: Reached target Local Encrypted Volumes.
[   11.644450] systemd[1]: Reached target Slices.
[   11.655220] systemd[1]: Reached target Swap.
[   11.665886] systemd[1]: Reached target System Time Set.
[   11.695157] systemd[1]: Listening on RPCbind Server Activation Socket.
[   11.707308] systemd[1]: Listening on Syslog Socket.
[   11.717971] systemd[1]: Listening on fsck to fsckd communication Socket.
[   11.729083] systemd[1]: Listening on initctl Compatibility Named Pipe.
[   11.740226] systemd[1]: Listening on Journal Audit Socket.
[   11.750140] systemd[1]: Listening on Journal Socket (/dev/log).
[   11.760412] systemd[1]: Listening on Journal Socket.
[   11.773613] systemd[1]: Listening on udev Control Socket.
[   11.783666] systemd[1]: Listening on udev Kernel Socket.
[   11.796379] systemd[1]: Mounting Huge Pages File System...
[   11.809523] systemd[1]: Mounting POSIX Message Queue File System...
[   11.822796] systemd[1]: Mounting RPC Pipe File System...
[   11.836017] systemd[1]: Mounting Kernel Debug File System...
[   11.846066] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   11.856717] RPC: Registered named UNIX socket transport module.
[   11.861718] RPC: Registered udp transport module.
[   11.866348] RPC: Registered tcp transport module.
[   11.867823] systemd[1]: Starting Restore / save the current clock...
[   11.871037] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   11.898241] systemd[1]: Starting Set the console keyboard layout...
[   11.912459] systemd[1]: Starting Create list of static device nodes for the current kernel...
[   11.925150] systemd[1]: Condition check resulted in Load Kernel Module drm being skipped.
[   11.928216] systemd[1]: Started Nameserver information manager.
[   11.943991] systemd[1]: Reached target Network (Pre).
[   11.957988] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   11.966174] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   11.980587] systemd[1]: Starting Load Kernel Modules...
[   11.993582] systemd[1]: Starting Remount Root and Kernel File Systems...
[   12.007846] systemd[1]: Starting udev Coldplug all Devices...
[   12.012913] usbcore: registered new interface driver r8152
[   12.025005] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[   12.027042] systemd[1]: Mounted Huge Pages File System.
[   12.043276] systemd[1]: Mounted POSIX Message Queue File System.
[   12.051635] usbcore: registered new interface driver ax88179_178a
[   12.058509] systemd[1]: Mounted RPC Pipe File System.
[   12.068316] systemd[1]: Mounted Kernel Debug File System.
[   12.079255] systemd[1]: Finished Restore / save the current clock.
[   12.091478] systemd[1]: Finished Create list of static device nodes for the current kernel.
[   12.109235] systemd[1]: Finished Load Kernel Modules.
[   12.120912] systemd[1]: Finished Remount Root and Kernel File Systems.
[   12.137093] systemd[1]: Mounting FUSE Control File System...
[   12.148432] crng init done
[   12.152758] random: 7 urandom warning(s) missed due to ratelimiting
[   12.159940] systemd[1]: Mounting Kernel Configuration File System...
[   12.178835] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   12.186281] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   12.199108] systemd[1]: Starting Load/Save Random Seed...
[   12.211726] systemd[1]: Starting Apply Kernel Variables...
[   12.224447] systemd[1]: Starting Create System Users...
[   12.238517] systemd[1]: Mounted FUSE Control File System.
[   12.248673] systemd[1]: Mounted Kernel Configuration File System.
[   12.357866] systemd[1]: Finished udev Coldplug all Devices.
[   13.773151] systemd[1]: Starting Helper to synchronize boot up for ifupdown...
[   13.818191] systemd[1]: Finished Load/Save Random Seed.
[   13.845922] systemd[1]: Finished Create System Users.
[   13.858925] systemd[1]: Starting Create Static Device Nodes in /dev...
[   13.884107] systemd[1]: Finished Apply Kernel Variables.
[   13.903234] systemd[1]: Finished Create Static Device Nodes in /dev.
[   13.919789] systemd[1]: Starting udev Kernel Device Manager...
[   14.020832] systemd[1]: Started udev Kernel Device Manager.
[   14.442656] meson_vdec: module is from the staging directory, the quality is unknown, you have been warned.
[   14.459390] Registered IR keymap rc-cec
[   14.470583] rc rc0: dw_hdmi as /devices/platform/soc/ff600000.bus/ff600000.hdmi-tx/rc/rc0
[   14.482276] input: dw_hdmi as /devices/platform/soc/ff600000.bus/ff600000.hdmi-tx/rc/rc0/input4
[   14.505323] Registered IR keymap rc-empty
[   14.511339] debugfs: Directory 'ff800280.cec' with parent 'regmap' already present!
[   14.511919] rc rc1: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1
[   14.522659] Registered IR keymap rc-cec
[   14.524943] systemd[1]: Found device /dev/ttyAML0.
[   14.531914] rc rc1: lirc_dev: driver meson-ir registered at minor = 0, raw IR receiver, no transmitter
[   14.545199] rc rc2: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc2
[   14.545318] input: meson_g12a_ao_cec as /devices/platform/soc/ff800000.bus/ff800280.cec/rc/rc2/input6
[   14.546178] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc1/input5
[   14.546393] meson-ir ff808000.ir: receiver initialized
[   14.583726] axg-sound-card sound: snd-soc-dummy-dai <-> ff6421c0.audio-controller mapping ok
[   14.605186] axg-sound-card sound: snd-soc-dummy-dai <-> ff642200.audio-controller mapping ok
[   14.619387] axg-sound-card sound: snd-soc-dummy-dai <-> ff642240.audio-controller mapping ok
[   14.644111] axg-sound-card sound: I2S IN B <-> TDM Pad mapping ok
[   14.665147] axg-sound-card sound: snd-soc-dummy-dai <-> TDM Loopback mapping ok
[   14.686235] axg-sound-card sound: multicodec <-> ff642480.audio-controller mapping ok
[   14.694710] axg-sound-card sound: SPDIF IN B <-> ff642680.audio-controller mapping ok
[   14.704747] axg-sound-card sound: i2s-hifi <-> I2S OUT mapping ok
[   14.710826] axg-sound-card sound: ASoC: no DMI vendor name!
[   14.744021] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   14.760221] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   14.767979] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   14.781093] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   14.789364] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   14.798863] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   14.810181] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   14.839733] [drm] kms: can't enable cloning when we probably wanted to.
[   14.956846] systemd[1]: Found device /sys/subsystem/net/devices/eth0.
[   15.103530] systemd[1]: Condition check resulted in Dispatch Password Requests to Console Directory Watch when bootsplash is active being skipped.
[   15.103882] systemd[1]: Condition check resulted in Kernel Trace File System being skipped.
[   15.104176] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[   15.143011] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   15.143202] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
[   15.143288] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[   15.176050] systemd[1]: Found device DataTraveler_3.0 BOOT.
[   15.289382] systemd[1]: Finished Helper to synchronize boot up for ifupdown.
[   15.613690] systemd[1]: Finished Set the console keyboard layout.
[   15.628865] systemd[1]: Reached target Local File Systems (Pre).
[   15.648813] systemd[1]: Mounting /var/tmp...
[   15.672545] systemd[1]: Starting File System Check on /dev/disk/by-label/BOOT...
[   15.690862] systemd[1]: Mounted /var/tmp.
[   15.707533] systemd[1]: Started File System Check Daemon to report status.
[   15.807373] systemd[1]: Finished File System Check on /dev/disk/by-label/BOOT.
[   15.824800] systemd[1]: Mounting /boot...
[   15.873175] systemd[1]: Mounted /boot.
[   15.886271] systemd[1]: Reached target Local File Systems.
[   15.903615] systemd[1]: Starting Armbian ZRAM config...
[   15.917411] systemd[1]: Starting Set console font and keymap...
[   15.932247] systemd[1]: Started ifup for eth0.
[   15.949506] systemd[1]: Starting Raise network interfaces...
[   15.968955] systemd[1]: Starting Preprocess NFS configuration...
[   15.980465] systemd[1]: Condition check resulted in Mark the need to relabel after reboot being skipped.
[   15.989245] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
[   15.998586] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
[   16.009734] systemd[1]: nfs-config.service: Succeeded.
[   16.016071] systemd[1]: Finished Preprocess NFS configuration.
[   16.026148] systemd[1]: Condition check resulted in RPC security service for NFS client and server being skipped.
[   16.035651] systemd[1]: Reached target NFS client services.
[   16.140097] zram: Added device: zram0
[   16.145278] zram: Added device: zram1
[   16.150325] zram: Added device: zram2
[   16.261659] zram0: detected capacity change from 0 to 491307008
[   16.306213] Adding 479788k swap on /dev/zram0.  Priority:5 extents:1 across:479788k SSFS
[   16.376721] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   16.381804] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   16.395886] zram1: detected capacity change from 0 to 52428800
[   16.447614] zram2: detected capacity change from 0 to 491307008
[   16.481148] EXT4-fs (zram2): mounted filesystem without journal. Opts: discard
[   16.487075] ext4 filesystem being mounted at /var/tmp supports timestamps until 2038 (0x7fffffff)
[   16.511168] systemd[1]: Finished Armbian ZRAM config.
[   16.523897] systemd[1]: Starting Armbian memory supported logging...
[   16.586813] EXT4-fs (zram1): mounted filesystem without journal. Opts: discard
[   16.592801] ext4 filesystem being mounted at /var/log supports timestamps until 2038 (0x7fffffff)
[   18.549735] systemd[1]: Finished Armbian memory supported logging.
[   18.564264] systemd[1]: Starting Journal Service...
[   18.717808] systemd[1]: Started Journal Service.
[   18.758521] systemd-journald[767]: Received client request to flush runtime journal.
[   24.706637] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   24.711229] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   24.829973] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   24.834557] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   24.919973] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   24.924490] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   25.009973] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   25.014509] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)
[   25.099973] meson8b-dwmac ff3f0000.ethernet eth0: no phy at addr -1
[   25.104503] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Cannot attach to PHY (error: -19)

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

commit 43dada6 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 30 20:26:38 2022 +0800 Add initial value commit 1b49c42 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 30 15:57:32 2022 +0800 Update firmware.tar.xz commit 570409d Author: ophub <ophub2020@gmail.com> Date: Wed Mar 30 09:33:48 2022 +0800 Fix modules-xxx.tar.gz path error commit 7825b7e Author: ophub <ophub2020@gmail.com> Date: Mon Mar 28 23:01:45 2022 +0800 Adjust the kernel module install path commit 816d96d Author: ophub <ophub2020@gmail.com> Date: Mon Mar 28 17:07:03 2022 +0800 Update external arm toolchains commit 716fc4b Author: ophub <ophub2020@gmail.com> Date: Sat Mar 26 22:02:20 2022 +0800 Adjust extlinux.conf default parameters commit a98c021 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 26 11:53:27 2022 +0800 Adjust files path commit 1556062 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 26 11:20:02 2022 +0800 Adjust file storage path commit 8c15768 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 26 11:16:25 2022 +0800 Adjust file storage path commit 1af334b Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 20:30:22 2022 +0800 Example of setting file system format settings commit 6b7ed54 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 20:09:00 2022 +0800 Update interfaces commit cb96c58 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 18:41:18 2022 +0800 Update rootfs path commit c7d3928 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 18:36:14 2022 +0800 Adjust document path commit f8e1a00 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 18:23:22 2022 +0800 Adjust file directory commit a66448a Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 18:05:59 2022 +0800 Add file system type setting description commit 8eb5e5f Author: ophub <ophub2020@gmail.com> Date: Fri Mar 25 17:36:47 2022 +0800 Add file system type setting option commit 5d931fb Author: ophub <ophub2020@gmail.com> Date: Wed Mar 23 22:11:50 2022 +0800 Add x96air.conf contributor commit bbc8a47 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 23 21:58:41 2022 +0800 Add x96air.conf for openvfd commit 0efe5a3 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 23 21:33:36 2022 +0800 Update the kernel compilation template commit e9f1eea Author: ophub <ophub2020@gmail.com> Date: Tue Mar 22 09:55:25 2022 +0800 Remove copy special dtb commit 158cb2d Author: ophub <ophub2020@gmail.com> Date: Tue Mar 22 09:14:40 2022 +0800 Optimize documentation commit 7e680c0 Author: ophub <ophub2020@gmail.com> Date: Tue Mar 22 09:07:27 2022 +0800 Add meson-gxl-s905l2-x7-5g.dtb for s905l2 (p281 board) commit 71448cc Author: ophub <ophub2020@gmail.com> Date: Mon Mar 21 21:30:21 2022 +0800 Update recovery system documentation commit 2e60d71 Author: ophub <ophub2020@gmail.com> Date: Mon Mar 21 20:39:37 2022 +0800 Adjust networking.service commit 07f45ef Author: ophub <ophub2020@gmail.com> Date: Mon Mar 21 17:10:23 2022 +0800 Remove T95-Plus device support commit 338ea09 Author: ophub <ophub2020@gmail.com> Date: Mon Mar 21 10:05:56 2022 +0800 Adjust startup files commit 13e8eea Author: ophub <ophub2020@gmail.com> Date: Sun Mar 20 20:45:58 2022 +0800 Add Armbian usage documentation commit 91301d3 Author: ophub <ophub2020@gmail.com> Date: Sun Mar 20 20:12:41 2022 +0800 Add LED screen display control instructions commit eab3afa Author: ophub <ophub2020@gmail.com> Date: Sun Mar 20 15:36:56 2022 +0800 Changed from uEnv.txt to extlinux.conf commit 1d8ba4b Author: ophub <ophub2020@gmail.com> Date: Sun Mar 20 11:17:11 2022 +0800 Add boot-common.tar.xz commit 614ec95 Author: ophub <ophub2020@gmail.com> Date: Sun Mar 20 11:11:50 2022 +0800 Add uEnv.txt commit 1d7c915 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 19 23:08:00 2022 +0800 Optimized armbian-install script commit e5e73a0 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 19 20:11:40 2022 +0800 Fix T95Z boot error commit c917139 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 19 18:44:58 2022 +0800 Supplemental led test documentation commit 9ea43bc Author: ophub <ophub2020@gmail.com> Date: Sat Mar 19 18:33:19 2022 +0800 Actions: Add custom options commit 51c6404 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 20:39:28 2022 +0800 openwrt-led: Adjust device serial number commit 7d712f5 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 18:25:20 2022 +0800 Improve LED test commands commit aabf2a5 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 14:30:56 2022 +0800 Add led file path description commit 280c260 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 14:05:22 2022 +0800 Add openvfd LED display contributor list commit 0fa7b05 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 13:36:14 2022 +0800 Added LED parameter adjustment instructions commit 22479d0 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 13:19:23 2022 +0800 Add list of devices that support LEDs commit c8e6579 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 18 13:04:29 2022 +0800 Add LED instructions commit 75f318f Author: ophub <ophub2020@gmail.com> Date: Thu Mar 17 13:54:04 2022 +0800 Update the kernel compilation template commit 9063d0d Author: ophub <ophub2020@gmail.com> Date: Wed Mar 16 17:42:11 2022 +0800 Add TX3-100Mb box support commit 86a2f88 Author: ophub <ophub2020@gmail.com> Date: Tue Mar 15 12:25:07 2022 +0800 Remove auto-replace source commit 21c65a0 Author: ophub <ophub2020@gmail.com> Date: Mon Mar 14 21:52:57 2022 +0800 Optimize code layout commit 58e8cca Author: ophub <ophub2020@gmail.com> Date: Sun Mar 13 19:40:20 2022 +0800 Add TX3 device display link commit b65e6c5 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 12 22:42:51 2022 +0800 Added Mecool-M8S-PRO-L device description commit 1ceb763 Author: ophub <ophub2020@gmail.com> Date: Sat Mar 12 22:28:21 2022 +0800 Add Mecool M8S PRO L commit 53568eb Author: ophub <ophub2020@gmail.com> Date: Fri Mar 11 22:59:23 2022 +0800 Update the kernel compilation template commit 1853fc2 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 11 20:24:54 2022 +0800 Perfect dtb file copy commit 1f279f2 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 11 17:09:06 2022 +0800 armbian-tf: use btrfs format commit 34ed1f5 Author: ophub <ophub2020@gmail.com> Date: Fri Mar 11 12:14:19 2022 +0800 Adjust the default system format to btrfs commit d15ee9c Author: ophub <ophub2020@gmail.com> Date: Thu Mar 10 22:07:20 2022 +0800 Adjust the unzip command commit 3988313 Author: ophub <ophub2020@gmail.com> Date: Thu Mar 10 21:48:48 2022 +0800 Adjust file results commit 3ce730b Author: ophub <ophub2020@gmail.com> Date: Thu Mar 10 19:56:34 2022 +0800 Add default script judgment commit 05decdb Author: ophub <ophub2020@gmail.com> Date: Wed Mar 9 22:44:52 2022 +0800 Remove useless code commit 1139e43 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 9 22:36:44 2022 +0800 Adjust the E900V22C device link commit 4c53056 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 9 15:14:15 2022 +0800 Update the kernel compilation template commit 5cead16 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 9 11:34:26 2022 +0800 Make the .bashrc take effect commit b3167c7 Author: ophub <ophub2020@gmail.com> Date: Thu Mar 3 12:40:48 2022 +0800 Adjust the soc list commit dcdcc52 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 21:06:12 2022 +0800 Adjust the default dtb of Beelink-Mini-MX commit f175f8f Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 20:54:44 2022 +0800 Update the kernel compilation template commit 6a95fc3 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 14:01:08 2022 +0800 Consolidate device lists commit 90f940a Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 11:54:02 2022 +0800 Added E900V22C device install option commit 9518419 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 11:52:48 2022 +0800 Added E900V22C contributor list commit 91f150e Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 09:29:02 2022 +0800 Add E900V22C product link commit 9b6fca4 Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 09:12:00 2022 +0800 Adjust the auxiliary recognition parameters commit 937d01a Author: ophub <ophub2020@gmail.com> Date: Wed Mar 2 09:05:45 2022 +0800 Instructions for adjusting s905l3a commit e7694bb Merge: f3ed9dd f2ba937 Author: ophub <68696949+ophub@users.noreply.github.com> Date: Wed Mar 2 08:52:46 2022 +0800 Merge pull request ophub#129 from Calmact/main Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. commit f2ba937 Author: Calmact <Calmact@gmail.com> Date: Tue Mar 1 23:36:55 2022 +0800 Update use-releases-file-to-build.yml commit 97dfce4 Author: Calmact <Calmact@gmail.com> Date: Tue Mar 1 22:54:58 2022 +0800 add MAINLINE_UBOOT="u-boot-u200.bin.sd.bin" commit f3ed9dd Author: ophub <ophub2020@gmail.com> Date: Tue Mar 1 17:47:01 2022 +0800 Add Beelink-Mini-MX-2G contributor: atsdai commit abf2111 Author: Calmact <Calmact@gmail.com> Date: Tue Mar 1 12:00:56 2022 +0800 first build commit 580871b Author: Calmact <Calmact@gmail.com> Date: Tue Mar 1 10:45:25 2022 +0800 rebuild add s905l3a for e900v22c commit 93a9bc0 Author: ophub <ophub2020@gmail.com> Date: Sun Feb 27 18:46:50 2022 +0800 rebuild: Add more notes commit f4fefc2 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 26 18:48:36 2022 +0800 Update the kernel compilation template commit b78bacb Author: ophub <ophub2020@gmail.com> Date: Sat Feb 26 17:18:32 2022 +0800 Adjust the number of releases to retain commit 56ec438 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 25 10:21:08 2022 +0800 Add Armbian system introduction commit df72ba8 Author: ophub <68696949+ophub@users.noreply.github.com> Date: Thu Feb 24 17:18:10 2022 +0800 Adjustment example commit f79bd34 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 24 17:15:14 2022 +0800 Default kernel bump to 5.15.y commit fcdf7d4 Author: ophub <ophub2020@gmail.com> Date: Wed Feb 23 17:26:14 2022 +0800 Update documentation commit 475943d Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 22:51:02 2022 +0800 Adjust output display commit fd12ece Author: ophub <68696949+ophub@users.noreply.github.com> Date: Tue Feb 22 22:12:19 2022 +0800 Add kernel directory description commit 173714b Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 19:05:21 2022 +0800 Update the u-boot download address commit ce80d42 Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 18:45:29 2022 +0800 update documentation commit 7a39642 Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 18:41:42 2022 +0800 Update ignore list commit 54859aa Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 17:47:02 2022 +0800 Adjust u-boot parameters commit 31d5192 Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 17:17:59 2022 +0800 Update ignore list commit c7d0092 Author: ophub <ophub2020@gmail.com> Date: Tue Feb 22 17:15:02 2022 +0800 Merge common dependency files commit ff4ebb5 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 19 22:25:23 2022 +0800 Complete the list of Armbian contributors commit f3e1a61 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 18 22:06:40 2022 +0800 Adjust Khadas VIM3 classification commit 39c85b8 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 18 20:17:47 2022 +0800 Added contributor for Khadas-VIM3 (A311D) commit f1fd9ca Author: ophub <ophub2020@gmail.com> Date: Fri Feb 18 20:06:31 2022 +0800 Add khadas vim3 install option commit f8ee930 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 18 15:34:40 2022 +0800 Adjust sync settings commit 6506b61 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 18 11:45:40 2022 +0800 Adjust to copy mode commit 8087272 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 17 23:52:33 2022 +0800 Optimize the rebuild logic commit a115076 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 17 19:43:20 2022 +0800 Optimize the rebuild process commit 6c8a7c3 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 17 17:36:12 2022 +0800 Adjust bootloader write timing commit e8c5270 Author: ophub <ophub2020@gmail.com> Date: Tue Feb 15 21:28:48 2022 +0800 recompile: Adjust function name commit 93b9b8c Author: ophub <ophub2020@gmail.com> Date: Mon Feb 14 19:02:44 2022 +0800 Adjust function name commit 39d05a4 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 14 16:57:22 2022 +0800 Update flippy's github link name commit 150e392 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 14 16:34:52 2022 +0800 Improve the update instructions commit 19f3aff Author: ophub <ophub2020@gmail.com> Date: Mon Feb 14 14:49:07 2022 +0800 Improve the kernel usage instructions commit 620cc5f Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 19:55:48 2022 +0800 Adjust the boot file processing order commit 5c454c8 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 16:53:27 2022 +0800 Update kernel compilation instructions commit 59bc821 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 15:20:05 2022 +0800 Add Acknowledgments list commit a17e131 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 14:33:15 2022 +0800 add ignore directory commit 8d1c4c3 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 14:32:48 2022 +0800 Adjust the default kernel version commit b8d7673 Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 12:20:45 2022 +0800 Update kernel instructions commit 6d28e7c Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 11:55:06 2022 +0800 Update kernel instructions commit 1c303be Author: ophub <ophub2020@gmail.com> Date: Sat Feb 12 10:19:24 2022 +0800 remove kernel files commit d6d35e2 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 11 18:07:42 2022 +0800 Add code snippet commit 1d7f472 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 11 14:39:25 2022 +0800 Optimize recompile script readability commit 3bc4ba9 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 11 14:38:53 2022 +0800 Optimize rebuild script readability commit 2d3869d Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 23:36:26 2022 +0800 Optimized lookup version information commit 47d6db8 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 21:33:07 2022 +0800 Optimize kernel compile logic commit c81b706 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 21:05:59 2022 +0800 Optimized kernel replace logic commit a2b55d2 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 18:54:23 2022 +0800 Adjustment process display commit 5c4171c Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 12:49:59 2022 +0800 Add toolchain download address commit a331759 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 10 12:31:13 2022 +0800 Add server information display commit e6c23ef Author: ophub <ophub2020@gmail.com> Date: Wed Feb 9 12:46:39 2022 +0800 Standard GPL-2.0 Declaration Format commit 867d510 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 7 21:55:22 2022 +0800 Adjust compile kernel parameters commit 2054f49 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 7 16:49:25 2022 +0800 Complete documentation commit f0dcae8 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 7 16:27:01 2022 +0800 Customize more parameter settings commit 29818f9 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 7 13:10:55 2022 +0800 restore startup interface commit 8ef7e70 Author: ophub <ophub2020@gmail.com> Date: Mon Feb 7 12:32:02 2022 +0800 add git ignore directory commit 8553a28 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 4 21:33:23 2022 +0800 Remove redundant code and files commit 4f49a5e Author: ophub <ophub2020@gmail.com> Date: Fri Feb 4 17:18:57 2022 +0800 Complete documentation commit 7aa8708 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 4 11:47:36 2022 +0800 armbian-docker: Adjust the version recognition method commit 7539ab7 Author: ophub <ophub2020@gmail.com> Date: Fri Feb 4 00:11:07 2022 +0800 armbian-docker: change to portainer-ce commit c057ae8 Author: ophub <ophub2020@gmail.com> Date: Thu Feb 3 16:29:15 2022 +0800 Optimize rebuild scripts commit 10be63b Author: ophub <ophub2020@gmail.com> Date: Thu Feb 3 13:02:16 2022 +0800 Adjust armbian firmware compilation parameters commit a097e7e Author: ophub <ophub2020@gmail.com> Date: Thu Feb 3 12:31:44 2022 +0800 ddbr renamed to armbian-ddbr commit 1d1d2db Author: ophub <ophub2020@gmail.com> Date: Fri Jan 28 18:25:31 2022 +0800 Complete documentation commit 9f8abb6 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 28 14:10:35 2022 +0800 Optimize custom templates commit d41d334 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 28 13:07:47 2022 +0800 Update kernel compilation instructions commit d99e130 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 28 12:16:39 2022 +0800 Improve kernel compilation commit 1b4a722 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 28 11:09:23 2022 +0800 Add custom compiled kernel .config file commit 8361a1a Author: ophub <ophub2020@gmail.com> Date: Thu Jan 27 22:46:55 2022 +0800 Add use actions compile kernel templates commit fd55012 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 27 16:38:19 2022 +0800 Optimizing Kernel Compiled Code commit 79be7d2 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 27 11:12:14 2022 +0800 Enable Linux Kernel Clang LTO commit 3fe2441 Author: ophub <ophub2020@gmail.com> Date: Wed Jan 26 13:03:33 2022 +0800 Adjusted to write to mainline u-boot by default commit 27db46e Author: ophub <68696949+ophub@users.noreply.github.com> Date: Tue Jan 25 23:05:04 2022 +0800 Adjust the clean command commit 1251074 Author: ophub <ophub2020@gmail.com> Date: Tue Jan 25 21:52:12 2022 +0800 The latest template is selected by default commit 16b7d71 Author: ophub <ophub2020@gmail.com> Date: Tue Jan 25 20:02:14 2022 +0800 Improve the kernel compilation script commit 1ccd883 Author: ophub <ophub2020@gmail.com> Date: Tue Jan 25 13:56:16 2022 +0800 Optimizing Kernel Compiled Code commit eabe120 Author: ophub <ophub2020@gmail.com> Date: Mon Jan 24 23:03:04 2022 +0800 update kernel compilation commit 03d16a0 Author: ophub <ophub2020@gmail.com> Date: Sun Jan 23 18:33:58 2022 +0800 Improve the documentation commit 2a4c1d4 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 22 20:07:02 2022 +0800 Change the default kernel to 5.10 commit bbcc637 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 22 11:58:39 2022 +0800 Adjust the UUID value commit c08dbd4 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 22 11:30:25 2022 +0800 Tweak dependency checking commit f804156 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 22 10:55:34 2022 +0800 fstab: change to UUID commit 5007019 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 23:50:12 2022 +0800 fstab: change to LABEL commit 7f0e4e3 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 21:06:33 2022 +0800 Adjust the gcc download address commit f16cc68 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 19:45:21 2022 +0800 kernel bump to 5.15 commit ab56402 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 16:02:27 2022 +0800 Check out the specified kernel branch commit 41fc6ef Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 14:41:27 2022 +0800 Auto sync upstream kernel source code commit bc378cc Author: ophub <ophub2020@gmail.com> Date: Fri Jan 21 11:13:06 2022 +0800 Improve -r parameter description commit d559ea9 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 20 23:48:45 2022 +0800 Improve code compatibility commit d51435e Author: ophub <ophub2020@gmail.com> Date: Thu Jan 20 20:27:06 2022 +0800 Optimize compile kernel code commit d295f37 Author: ophub <ophub2020@gmail.com> Date: Tue Jan 18 16:37:38 2022 +0800 disable hdmi.rules commit 800bd0e Author: ophub <ophub2020@gmail.com> Date: Tue Jan 18 14:03:41 2022 +0800 Unified error output messages commit 2918d6d Author: ophub <ophub2020@gmail.com> Date: Tue Jan 18 13:41:08 2022 +0800 Support automatic query and update commit 9e7a232 Author: ophub <ophub2020@gmail.com> Date: Mon Jan 17 20:19:01 2022 +0800 Update installation instructions commit 50c7355 Author: ophub <ophub2020@gmail.com> Date: Sun Jan 16 21:28:23 2022 +0800 Fix error commit baf51c3 Author: ophub <ophub2020@gmail.com> Date: Sun Jan 16 21:07:09 2022 +0800 Adjust the default kernel commit 3970e33 Author: ophub <ophub2020@gmail.com> Date: Sun Jan 16 17:19:16 2022 +0800 Adjust boot file commit 3ada6f4 Author: ophub <ophub2020@gmail.com> Date: Sun Jan 16 14:38:09 2022 +0800 Added support for MECOOL KM3 commit 5b96eb1 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 15 11:08:41 2022 +0800 s922x-reva: Add parameter description commit a6ba23a Author: ophub <ophub2020@gmail.com> Date: Sat Jan 15 10:52:36 2022 +0800 Adjust default configuration commit 8d3703d Author: ophub <ophub2020@gmail.com> Date: Fri Jan 14 23:41:22 2022 +0800 Adjust default compilation commit 57444f6 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 14 22:51:05 2022 +0800 Added Tanix-TX92 information by ErikPelli commit aef1caf Author: ophub <ophub2020@gmail.com> Date: Fri Jan 14 21:28:26 2022 +0800 Try Beelink GT-King Pro Rev_A (beta) commit 9ae62a8 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 13 16:05:16 2022 +0800 Modify banner file permissions commit 8e51442 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 13 12:39:25 2022 +0800 Adjust default compilation commit 3909859 Author: ophub <ophub2020@gmail.com> Date: Thu Jan 13 11:36:18 2022 +0800 Adjust default compilation commit 1339584 Author: ophub <ophub2020@gmail.com> Date: Wed Jan 12 23:19:50 2022 +0800 Add rtl8189fs & rtl8822cs driver for dev commit 12bc55e Author: ophub <ophub2020@gmail.com> Date: Wed Jan 12 22:04:47 2022 +0800 Adjust default compilation commit 396cf67 Author: ophub <ophub2020@gmail.com> Date: Tue Jan 11 13:25:51 2022 +0800 Fix banner display permissions commit a8c0081 Author: ophub <ophub2020@gmail.com> Date: Mon Jan 10 21:20:16 2022 +0800 Adjust release file commit b95c4ec Author: ophub <ophub2020@gmail.com> Date: Mon Jan 10 15:57:19 2022 +0800 Adjust VERSION_CODENAME to get files commit 2671631 Author: ophub <ophub2020@gmail.com> Date: Sat Jan 8 18:19:32 2022 +0800 Update CustomName commit 6118a47 Merge: 1ad86ee 39d5756 Author: ophub <68696949+ophub@users.noreply.github.com> Date: Sat Jan 8 15:02:42 2022 +0800 Merge pull request ophub#65 from 0neday/patch-1 Update README.md commit 39d5756 Author: COOLSTAR <guanyin9.cn@gmail.com> Date: Sat Jan 8 01:47:47 2022 -0500 Update README.md commit 1ad86ee Author: ophub <ophub2020@gmail.com> Date: Sat Jan 8 10:21:56 2022 +0800 Add compression function commit 6f3e195 Author: ophub <ophub2020@gmail.com> Date: Fri Jan 7 17:57:33 2022 +0800 Update kernel .config template commit f4b696e Author: ophub <ophub2020@gmail.com> Date: Wed Jan 5 23:46:44 2022 +0800 Update kernel template commit e5882f1 Author: ophub <ophub2020@gmail.com> Date: Wed Jan 5 18:06:47 2022 +0800 Adjust the default kernel commit e572603 Author: ophub <ophub2020@gmail.com> Date: Wed Jan 5 12:55:55 2022 +0800 Update device description commit 8819b6b Author: ophub <ophub2020@gmail.com> Date: Tue Jan 4 18:41:23 2022 +0800 Update compilation parameters commit 6ace7fe Author: ophub <ophub2020@gmail.com> Date: Mon Jan 3 11:51:14 2022 +0800 Adjust the prompt font color commit cf08a48 Author: ophub <ophub2020@gmail.com> Date: Mon Jan 3 11:06:46 2022 +0800 Add the default build 5.15 kernel commit 147e376 Author: ophub <ophub2020@gmail.com> Date: Mon Jan 3 10:38:58 2022 +0800 Add the default build 5.15 kernel commit 70d233b Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 20:24:22 2021 +0800 Remove support for Bionic commit 03e4875 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 17:34:35 2021 +0800 Add more build options for compile.sh commit 2e0fc98 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 14:05:49 2021 +0800 armbian-docker: Adjust the default to Ubuntu commit f08afb6 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 13:33:33 2021 +0800 Adjust the default to focal commit f980db3 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 12:59:14 2021 +0800 Adjust the kernel branch name beta to dev commit 9068519 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 30 12:49:05 2021 +0800 Fix spelling errors commit 3aa7ff3 Author: ophub <ophub2020@gmail.com> Date: Wed Dec 29 14:02:31 2021 +0800 Update device link commit 778c7d7 Author: ophub <ophub2020@gmail.com> Date: Tue Dec 28 17:04:42 2021 +0800 remove upload-artifact commit 0856f59 Author: ophub <ophub2020@gmail.com> Date: Tue Dec 28 16:03:11 2021 +0800 Add s905 description commit 7316af7 Author: ophub <ophub2020@gmail.com> Date: Tue Dec 28 15:30:42 2021 +0800 Added s905 support commit 511b31d Author: ophub <ophub2020@gmail.com> Date: Wed Dec 22 17:59:06 2021 +0800 Optimize code display commit 9d58836 Author: ophub <ophub2020@gmail.com> Date: Mon Dec 20 15:33:02 2021 +0800 Update full name commit 796dae6 Author: ophub <ophub2020@gmail.com> Date: Mon Dec 20 15:13:19 2021 +0800 Update full name commit cb32d0b Author: ophub <ophub2020@gmail.com> Date: Mon Dec 20 14:21:24 2021 +0800 Cancel timed compilation commit 1de79ee Author: ophub <ophub2020@gmail.com> Date: Fri Dec 17 11:56:45 2021 +0800 armbian-docker: Support choosing to install portainer commit a2ee65d Author: ophub <ophub2020@gmail.com> Date: Wed Dec 15 17:59:31 2021 +0800 armbian-docker: add portainer commit 5dfb51f Author: ophub <ophub2020@gmail.com> Date: Tue Dec 14 22:06:53 2021 +0800 armbian-tf: optional expansion or creation partition commit 7ae7faf Author: ophub <ophub2020@gmail.com> Date: Tue Dec 14 17:46:26 2021 +0800 ddbr: Add description of backup/restore tv system commit 7ae22a1 Author: ophub <ophub2020@gmail.com> Date: Fri Dec 10 22:09:41 2021 +0800 Add QEMU BINARY to chroot target commit b7629d7 Author: ophub <ophub2020@gmail.com> Date: Wed Dec 8 19:22:32 2021 +0800 Optimize yml file commit 8cf41ec Author: ophub <ophub2020@gmail.com> Date: Wed Dec 8 16:52:11 2021 +0800 Adjust version matching commit b407eb5 Author: ophub <ophub2020@gmail.com> Date: Wed Dec 8 11:44:19 2021 +0800 Adjust the default firmware to bullseye commit 8f046e2 Author: ophub <ophub2020@gmail.com> Date: Sun Dec 5 21:09:53 2021 +0800 Add set OS release instructions commit eaf6715 Author: ophub <ophub2020@gmail.com> Date: Sun Dec 5 11:41:56 2021 +0800 Add backup source commit 1819275 Author: ophub <ophub2020@gmail.com> Date: Sun Dec 5 10:47:32 2021 +0800 Add: delete old version and artifacts commit 78a3699 Author: ophub <ophub2020@gmail.com> Date: Sun Dec 5 10:19:17 2021 +0800 Adjust the difference file copy plan commit 76f8e0f Author: ophub <ophub2020@gmail.com> Date: Sun Dec 5 00:57:08 2021 +0800 Add multiple release support commit 844d8b3 Author: ophub <ophub2020@gmail.com> Date: Sat Dec 4 11:48:32 2021 +0800 Add armbian rebuild example commit 0ebe3f2 Author: ophub <ophub2020@gmail.com> Date: Sat Dec 4 08:08:09 2021 +0800 Support Actions to introduce rebuild commit de4df52 Author: ophub <ophub2020@gmail.com> Date: Thu Dec 2 15:27:02 2021 +0800 Optimized code commit d60365d Author: ophub <ophub2020@gmail.com> Date: Thu Dec 2 12:50:35 2021 +0800 Fixed mac address commit 90927bc Author: ophub <ophub2020@gmail.com> Date: Wed Dec 1 22:06:15 2021 +0800 armbian-update: unified error output commit 96be5d1 Author: ophub <ophub2020@gmail.com> Date: Wed Dec 1 21:45:13 2021 +0800 armbian-update: install the current directory kernel commit 4238ad3 Author: ophub <ophub2020@gmail.com> Date: Wed Dec 1 19:07:10 2021 +0800 Adjust the armbian download strategy commit 85124bc Author: ophub <ophub2020@gmail.com> Date: Wed Dec 1 17:47:11 2021 +0800 Improve the cross-compilation kernel commit ad0a839 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 26 21:09:29 2021 +0800 Complete description commit 3f61d1b Author: ophub <ophub2020@gmail.com> Date: Fri Nov 26 19:03:37 2021 +0800 Modify the Armbian kernel update script commit 102e616 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 26 17:34:11 2021 +0800 Update Armbian contributor list commit 36194da Author: ophub <ophub2020@gmail.com> Date: Tue Nov 23 09:05:32 2021 +0800 Adjust the kernel's default compilation source: flippy commit 1efcf42 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 22 22:20:32 2021 +0800 Modify the kernel compilation command commit f3e0f69 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 22 21:36:01 2021 +0800 Complete description commit 89ba5f8 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 22 21:27:18 2021 +0800 Update kernel compilation template commit ec301bd Author: ophub <ophub2020@gmail.com> Date: Mon Nov 22 14:53:49 2021 +0800 Update armbian pioneer list commit fecec53 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 22 12:35:46 2021 +0800 Add .gitignore file commit cc1436d Author: ophub <ophub2020@gmail.com> Date: Sun Nov 21 19:40:25 2021 +0800 Adjust the path of the package header file commit 94ecd37 Author: ophub <ophub2020@gmail.com> Date: Sun Nov 21 17:33:26 2021 +0800 Adjust the default installation path of headers files commit 145e017 Author: ophub <ophub2020@gmail.com> Date: Sun Nov 21 11:26:38 2021 +0800 armbian-update: add automatic update commit 176f431 Author: ophub <ophub2020@gmail.com> Date: Sat Nov 20 23:04:48 2021 +0800 Add meson-gxl-s905l2-p281.dtb shared by NewbieOrange commit 0f6042a Author: ophub <ophub2020@gmail.com> Date: Sat Nov 20 22:51:27 2021 +0800 Add kernel header files when rebuild armbian commit 1dcc61a Author: ophub <ophub2020@gmail.com> Date: Sat Nov 20 22:17:45 2021 +0800 Add compile and install kernel header files commit 44fdc1c Author: ophub <ophub2020@gmail.com> Date: Sat Nov 20 16:55:57 2021 +0800 Edit description text commit 50dddac Author: ophub <ophub2020@gmail.com> Date: Sat Nov 20 12:09:23 2021 +0800 Add the Armbian pioneer list commit ce5dcce Author: ophub <ophub2020@gmail.com> Date: Fri Nov 19 16:11:49 2021 +0800 kernel: bump to 5.10.80 and 5.4.160 commit 68a1394 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 19 09:25:34 2021 +0800 Improve documentation commit 965fdca Author: ophub <ophub2020@gmail.com> Date: Fri Nov 19 07:55:31 2021 +0800 Add flippy source code version query commit dff921b Author: ophub <ophub2020@gmail.com> Date: Thu Nov 18 17:38:53 2021 +0800 Support the use of flippy's source code to compile the kernel commit 8babe29 Author: ophub <ophub2020@gmail.com> Date: Thu Nov 18 13:23:19 2021 +0800 Adjust the uInitrd file usage strategy commit a8fc44d Author: ophub <ophub2020@gmail.com> Date: Wed Nov 17 22:13:02 2021 +0800 Optimize kernel compilation logic commit bfd0394 Author: ophub <ophub2020@gmail.com> Date: Wed Nov 17 17:34:01 2021 +0800 Adjust the default settings commit 6ee7d06 Author: ophub <ophub2020@gmail.com> Date: Wed Nov 17 16:00:56 2021 +0800 Adjust the kernel compilation command commit a366dbd Author: ophub <ophub2020@gmail.com> Date: Wed Nov 17 09:44:11 2021 +0800 Adjust the armbian build command commit bed1646 Author: ophub <ophub2020@gmail.com> Date: Tue Nov 16 23:04:53 2021 +0800 tidy up code commit 47b0374 Author: ophub <ophub2020@gmail.com> Date: Tue Nov 16 17:59:06 2021 +0800 Add the function of compiling the kernel commit e4bd443 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 15 21:03:36 2021 +0800 Adjust the directory name commit f5bb397 Author: ophub <ophub2020@gmail.com> Date: Mon Nov 15 13:03:13 2021 +0800 s912 T95Z-Plus: Add support commit 92638c5 Author: ophub <ophub2020@gmail.com> Date: Sun Nov 14 19:43:39 2021 +0800 Fix spelling errors commit e59008f Author: ophub <ophub2020@gmail.com> Date: Sun Nov 14 19:32:50 2021 +0800 polkit-agent-helper-1: Repair permissions commit a20ebe8 Author: ophub <ophub2020@gmail.com> Date: Sun Nov 14 17:20:59 2021 +0800 Add sudo file permissions commit d6506d7 Author: ophub <ophub2020@gmail.com> Date: Sat Nov 13 18:30:01 2021 +0800 Adjustment tips commit 1862913 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 12 18:38:16 2021 +0800 Organize the code commit 4b6bf82 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 12 15:54:23 2021 +0800 Adjust the repository address link commit 0dbaab9 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 12 15:45:57 2021 +0800 Change the kernel repository commit bdc011f Author: ophub <ophub2020@gmail.com> Date: Sat Nov 6 20:26:01 2021 +0800 Optimize the display of instructions commit 0bcac19 Author: ophub <ophub2020@gmail.com> Date: Fri Nov 5 17:21:45 2021 +0800 Delete unnecessary files commit d074e4e Author: ophub <ophub2020@gmail.com> Date: Thu Nov 4 19:58:43 2021 +0800 Add armbian-swap commit 73b387c Author: ophub <ophub2020@gmail.com> Date: Sun Oct 31 16:46:16 2021 +0800 Adjust the installation menu commit efa3ebb Author: ophub <ophub2020@gmail.com> Date: Sat Oct 23 13:24:07 2021 +0800 Strengthen the armbian-tf script commit 66f31c4 Author: ophub <ophub2020@gmail.com> Date: Thu Oct 21 20:36:26 2021 +0800 Adjust the display of README commit 26cd301 Author: ophub <ophub2020@gmail.com> Date: Thu Oct 21 11:43:05 2021 +0800 Add again manual setting TF/USB instructions commit 2590925 Author: ophub <ophub2020@gmail.com> Date: Thu Oct 21 11:39:55 2021 +0800 Add actions support for s922x-odroid-n2 commit 5e0b78a Author: ophub <ophub2020@gmail.com> Date: Wed Oct 20 20:14:36 2021 +0800 Add manual setting TF/USB instructions commit 2a5fd99 Author: ophub <ophub2020@gmail.com> Date: Wed Oct 20 17:33:00 2021 +0800 Add partition creation script when using TF/USB commit 22722ed Author: ophub <ophub2020@gmail.com> Date: Tue Oct 19 15:13:54 2021 +0800 Added instructions for using Armbian in TF/USB commit 3788195 Author: ophub <ophub2020@gmail.com> Date: Fri Oct 15 13:00:40 2021 +0800 Add the acknowledgments commit 35afa4e Author: ophub <ophub2020@gmail.com> Date: Wed Oct 13 09:41:03 2021 +0800 Add sync operator commit 92f9014 Author: ophub <ophub2020@gmail.com> Date: Mon Oct 11 16:10:35 2021 +0800 Add command description commit 3742482 Author: ophub <ophub2020@gmail.com> Date: Sat Oct 9 22:40:01 2021 +0800 Tuning the kernel commit b724d2c Author: ophub <ophub2020@gmail.com> Date: Mon Oct 4 20:51:35 2021 +0800 Fix mandb Operation not permitted commit 9563082 Author: ophub <ophub2020@gmail.com> Date: Sun Oct 3 17:53:10 2021 +0800 Add optional board commit f9d3ba1 Author: ophub <ophub2020@gmail.com> Date: Sat Oct 2 16:51:13 2021 +0800 Delete SSH connection to Actions commit c2d8684 Author: ophub <ophub2020@gmail.com> Date: Thu Sep 30 07:57:07 2021 +0800 Custom BOARD_NAME commit 6d726ac Author: ophub <ophub2020@gmail.com> Date: Wed Sep 29 11:49:28 2021 +0800 Optimize the replace kernel logic commit 7d2645b Author: ophub <ophub2020@gmail.com> Date: Tue Sep 28 23:24:51 2021 +0800 Add examples and instructions for replacing the kernel commit 7e6fcad Author: ophub <ophub2020@gmail.com> Date: Tue Sep 28 22:24:54 2021 +0800 Optimize compilation logic commit 68da9be Author: ophub <ophub2020@gmail.com> Date: Tue Sep 28 17:25:50 2021 +0800 Kernel can be changed during compilation commit 9be52c0 Author: ophub <ophub2020@gmail.com> Date: Thu Sep 23 19:44:14 2021 +0800 Add local production instructions commit ff5ead8 Author: ophub <ophub2020@gmail.com> Date: Tue Sep 21 10:12:55 2021 +0800 Add BOARD_NAME parameter commit 462fc15 Author: ophub <ophub2020@gmail.com> Date: Mon Sep 20 16:30:40 2021 +0800 Add use releases file to build commit c1fa5a1 Author: ophub <ophub2020@gmail.com> Date: Mon Sep 20 15:37:19 2021 +0800 Adjust file storage plan commit d538c4a Author: ophub <ophub2020@gmail.com> Date: Mon Sep 20 11:04:12 2021 +0800 Adjust the default compiled soc type commit 6a836f2 Author: ophub <ophub2020@gmail.com> Date: Mon Sep 20 10:56:54 2021 +0800 Update install script commit f3af1cd Author: ophub <ophub2020@gmail.com> Date: Sun Sep 19 20:37:14 2021 +0800 Adjust the compilation list commit c9bcfbb Author: ophub <ophub2020@gmail.com> Date: Sun Sep 19 19:43:08 2021 +0800 Update readme commit 1dfb967 Author: ophub <ophub2020@gmail.com> Date: Sun Sep 19 17:34:33 2021 +0800 Add actions online compilation function commit 9e11d4d Author: ophub <ophub2020@gmail.com> Date: Sun Sep 19 17:31:55 2021 +0800 Release the first version

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

Calmact added 4 commits March 1, 2022 10:45

rebuild add s905l3a for e900v22c

676e93a

first build

97a9ac6

add MAINLINE_UBOOT="u-boot-u200.bin.sd.bin"

e591e6e

Update use-releases-file-to-build.yml

29d5e0c

Calmact changed the title ~~Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips of e900v22c/22d, etc.~~ Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. Mar 1, 2022

ophub merged commit fe3ce2b into ophub:main Mar 2, 2022

ophub added a commit that referenced this pull request Mar 9, 2022

Merge pull request #129 from Calmact/main

ef6e5c2

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 10, 2022

Merge pull request #129 from Calmact/main

d971fa3

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 11, 2022

Merge pull request #129 from Calmact/main

cdb6bc5

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 12, 2022

Merge pull request #129 from Calmact/main

1ee35da

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 20, 2022

Merge pull request #129 from Calmact/main

882cd4f

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 25, 2022

Merge pull request #129 from Calmact/main

c9d6493

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Mar 26, 2022

Merge pull request #129 from Calmact/main

e7694bb

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub mentioned this pull request Apr 4, 2022

e900v22c 5.15内核安装进emmc后不能启动 #222

Closed

KryptonLee mentioned this pull request Apr 9, 2022

使用uEnv.txt配置文件和extlinux/extlinux.conf配置文件的区别是什么？ #229

Closed

ophub added a commit that referenced this pull request May 16, 2022

Merge pull request #129 from Calmact/main

7550227

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Jun 7, 2022

Merge pull request #129 from Calmact/main

dffb131

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Jun 17, 2022

Merge pull request #129 from Calmact/main

bcae714

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

ophub added a commit that referenced this pull request Jun 25, 2022

Merge pull request #129 from Calmact/main

151c8a8

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. #129

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. #129

Calmact commented Mar 1, 2022 •

edited

Loading

Calmact commented Mar 1, 2022

Calmact commented Mar 1, 2022

Calmact commented Mar 1, 2022

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. #129

Added s905l3a in rebuild to support S905L 3A/S905L 3A-B chips for e900v22c/22d, etc. #129

Conversation

Calmact commented Mar 1, 2022 • edited Loading

Calmact commented Mar 1, 2022

Calmact commented Mar 1, 2022

Calmact commented Mar 1, 2022

Calmact commented Mar 1, 2022 •

edited

Loading